Sony VPL-VW200 Manual
65
Ot
hers
hers
Replacing the Lamp
and the Air Filter and
cleaning the
Ventilation holes
(intake)
and the Air Filter and
cleaning the
Ventilation holes
(intake)
Tools you need to get started:
Standard Phillips screwdriver
Cloth (for scratch protection)
The lamp used for the light source has a
certain lifespan. When the lamp dims, the
color balance of the picture becomes
strange, or “Please replace the Lamp/Filter.
End of Lamp/Filter life. Lamp off in 1 min.”
appears on the screen, the lamp may be
exhausted. Replace the lamp with a new one
(not supplied)
Standard Phillips screwdriver
Cloth (for scratch protection)
The lamp used for the light source has a
certain lifespan. When the lamp dims, the
color balance of the picture becomes
strange, or “Please replace the Lamp/Filter.
End of Lamp/Filter life. Lamp off in 1 min.”
appears on the screen, the lamp may be
exhausted. Replace the lamp with a new one
(not supplied)
without delay.
Use an LMP-H400 Projector Lamp as the
replacement lamp.
The air filter is supplied with the LMP-H400
Projector Lamp. When you replace the lamp,
it is also time to replace the air filter.
Whenever you replace the lamp, be sure to
replace the air filter with a new one. Also
clean the ventilation holes (intake).
replacement lamp.
The air filter is supplied with the LMP-H400
Projector Lamp. When you replace the lamp,
it is also time to replace the air filter.
Whenever you replace the lamp, be sure to
replace the air filter with a new one. Also
clean the ventilation holes (intake).
• The lamp remains hot after the projector is
turned off with the ?/1 (ON/STANDBY)
switch. If you touch the lamp, you may burn
your fingers. When you replace the lamp,
wait for at least an hour for the lamp to cool.
switch. If you touch the lamp, you may burn
your fingers. When you replace the lamp,
wait for at least an hour for the lamp to cool.
• Do not touch the surface of the lens. If you
touch it, wipe off the fingerprints with a
soft cloth.
soft cloth.
• Pay special attention to replacing the lamp
when the projector is installed on the ceiling.
• When removing the lamp unit, make sure it
remains horizontal, then pull straight up. Do
not tilt the lamp unit. If you pull out the lamp
unit while tilted and if the lamp breaks, the
pieces may scatter, causing injury.
not tilt the lamp unit. If you pull out the lamp
unit while tilted and if the lamp breaks, the
pieces may scatter, causing injury.
• When you remove the air filter, be careful
not to let any dust fall into the projector.
• Replacing the air filter is crucial to maintain
the good performance of the projector or to
prevent malfunction to it. When a warning
message for replacing the air filter appears,
replace the air filter immediately.
prevent malfunction to it. When a warning
message for replacing the air filter appears,
replace the air filter immediately.
1
Turn off the projector and
unplug the AC power cord.
unplug the AC power cord.
2
When setting the projector on a
flat surface such as a desk etc.,
put a cloth to prevent the surface
from being scratched. Reverse
the projector as illustrated, then
place it on the cloth.
flat surface such as a desk etc.,
put a cloth to prevent the surface
from being scratched. Reverse
the projector as illustrated, then
place it on the cloth.
Be sure that the projector is placed on a
stable surface.
stable surface.
3
While holding up the cover
release lever on the right, slide
the top cover until it stops.
release lever on the right, slide
the top cover until it stops.
4
Loosen the screw on the lamp
cover with a Philips screwdriver,
and then open the lamp cover.
cover with a Philips screwdriver,
and then open the lamp cover.
Be sure to use a Philips screwdriver with a
shaft length of 130 mm (5
shaft length of 130 mm (5
1
/
8
inches) or
more when replacing a projector lamp.
Caution
Note
Note
Cover release lever