Yamaha GX-700 User Manual
E-28
DISC
1
DISC
2
DISC
3
DOWN
UP
VOLUME
STANDBY/ON
PROGRAM
B.BOOST
MUSIC
INPUT
INPUT
MIN
PRESET/ TUNING/ BAND
A/B/C/D/E
DISC CHANGE
OPEN / CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSE
DOLBY NR
HOUR
RANDOM
REPEAT
TIME
DISPLAY
MODE
M
PROG
VOLUME
A
OVER 15
1 2 3 4
7 8 9 10
7 8 9 10
13 14 15
5
11
6
12
REM
TRACK
CD
NR
KK
AM
C HALL
YMERSION
EDIT
PROG
S F REP
VOLUME
A
B
OVER 15
1 2 3 4
7 8 9 10
7 8 9 10
13 14 15
5
11
6
12
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM
TUNER
CD
MD
TAPE
NR
PROGRAM
BASS
BOOST
MUSIC
CENTER/
REAR/DELAY
TEST
LEVEL
VOLUME
POWER
SLEEP
/I
REC/PAUSE
DIRECTION
TAPE
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
0
TIME
PROG
R. TIME
C
EDIT
D
PRESET
+
I0
E
MODE
REPEAT
RANDOM
TUNER
DISC SKIP
A
B
TUNER CD
INPUT
Recording
m
Manual EDIT recording
You can program tracks manually while watching the
remaining time on both sides of the tape.
remaining time on both sides of the tape.
1
Press INPUT
or
once or more until “CD” (
1
,
5
)
appears on the display, and load a disc (or discs) on the
disc tray.
disc tray.
2
Follow steps 3–5 on page 26.
3
Press PROG.
* “PROG” and “P-01” will light up on the display, and all
* “PROG” and “P-01” will light up on the display, and all
track numbers on the selected disc will begin flashing.
4
If necessary, select the desired disc by pressing DISC
SKIP.
SKIP.
5
Select the desired track number by pressing the numeric
buttons.
buttons.
6
Repeat steps 4 and 5 to program more selections for side A
of the tape. You can select the same track again.
* Pressing TIME displays the total remaining time on side
of the tape. You can select the same track again.
* Pressing TIME displays the total remaining time on side
A of the tape for about 1 second, and then it is replaced
by the display of the next play order.
by the display of the next play order.
* If “TM OVER” appears on the display, the track number
just selected cannot be programmed because there is
not enough time remaining on side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program it
instead of the unprogrammable one.
not enough time remaining on side A of the tape.
However, at this time, if any other track number is
flashing continuously on the display, you can program it
instead of the unprogrammable one.
7
When the programming for side A is finished, press
R. TIME.
* “Side-B” appears on the display. You can begin
R. TIME.
* “Side-B” appears on the display. You can begin
programming for side B.
* After following this step, you can check the programmed
contents for side A and side B alternately by pressing
R. TIME at any time before you press EDIT in step 9.
R. TIME at any time before you press EDIT in step 9.
* The tape side indicator (
9
) shows the programming
side currently selected.
8
Repeat steps 4 and 5 to program selections for side B of
the tape. You can select the same track again.
the tape. You can select the same track again.
9
Press EDIT. (“EDIT” (
8
) lights up on the display.)
The recording starts.
1
1
3
4
5
7
9
Display information during programming
Notes on recording with the EDIT function
●
To check, cancel or correct program data, refer to page 14.
●
The maximum number of tracks that can be programmed is
20.
20.
●
The track number 16 or higher cannot be programmed by
this function.
this function.
TIME
TIME
Selected disc
Side of the tape
Next play order
Programmed track numbers light up
and only programmable track numbers
among unprogrammed ones flash.
and only programmable track numbers
among unprogrammed ones flash.
Selected track
number
number
Total remaining time on
this side of the tape
this side of the tape