Yamaha RX-V2700 Owner's Manual
140
En
TROUBLESHOOTING
Problem
Cause
Remedy
See
page
No picture.
The output and input for the picture are
connected to different types of video
jacks.
connected to different types of video
jacks.
Set “Conversion” to “On” or connect your source
components in the same way as you connect your
video monitor to this unit.
components in the same way as you connect your
video monitor to this unit.
Non-standard video signals are input.
Short message
displays do not
appear in the video
monitor.
displays do not
appear in the video
monitor.
“Short Message” is set to “OFF”.
Set “Short Message” to “On”.
“Wall Paper” is set to “None”.
Set “Wall Paper” to “Yes” or “Gray”.
“Conversion” is set to “Off”.
Set “Conversion” to “On”.
The signals input at the HDMI IN1,
HDMI IN2 or HDMI IN3 jack are being
output at the HDMI OUT jack.
HDMI IN2 or HDMI IN3 jack are being
output at the HDMI OUT jack.
Video signals in the progressive format or
HDTV video signals are being input.
HDTV video signals are being input.
The sound suddenly
goes off.
goes off.
The protection circuitry has been activated
because of a short circuit, etc.
because of a short circuit, etc.
Check that the speaker impedance setting is correct.
Check that the speaker wires are not touching each
other and then turn this unit back on.
other and then turn this unit back on.
—
The sleep timer has turned off this unit.
Turn on this unit, and play the source again.
—
The sound is muted.
Press MUTE or VOLUME +/– on the remote control
to resume audio output.
to resume audio output.
Sound is heard from
the speaker on one
side only.
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
the cables may be defective.
Incorrect settings in “Speaker Level”.
Adjust the “Speaker Level” settings.
Only the center
speaker outputs
substantial sound.
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
from the center
speaker.
“Center” in “Speaker Set” is set to
“None”.
“None”.
Set “Center” to “Small” or “Large”.
One of the HiFi DSP programs (except for
“7ch Stereo”) has been selected.
“7ch Stereo”) has been selected.
Try another sound field program.
No sound is heard
from the presence
speakers.
from the presence
speakers.
The sound field programs are turned off.
Press STRAIGHT to turn them on.
You are using a source or program
combination that does not output sound
from all channels.
combination that does not output sound
from all channels.
Try another sound field program.
No sound is heard
from the surround
speakers.
from the surround
speakers.
“Surround” in “Speaker Set” is set to
“None”.
“None”.
Set “Surround” to “Small” or “Large”.
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
and a monaural source is being played
back.
Press STRAIGHT on the front panel so that
“STRAIGHT” disappears from the front panel
display.
“STRAIGHT” disappears from the front panel
display.
No sound is heard
from the subwoofer.
from the subwoofer.
“Bass Out” in “Speaker Set” is set to
“Front” when a Dolby Digital or DTS
signal is being played.
“Front” when a Dolby Digital or DTS
signal is being played.
Set “Bass Out” to “SWFR” or “Both”.
“Bass Out” in “Speaker Set” is set to
“SWFR” or “Front” when a 2-channel
source is being played.
“SWFR” or “Front” when a 2-channel
source is being played.
Set “Bass Out” to “Both”.
The source does not contain low-
frequency signals.
frequency signals.