Yamaha HS10W User Manual
English
HS80M/HS50M/HS10W Owner’s Manual
13
HS10W
!
POWER switch
Turns power to the speaker on or off. When the power is
turned on the tuning fork mark on the front panel will light.
turned on the tuning fork mark on the front panel will light.
"
INPUT L/R connector
These are balanced XLR-type and phone type input
connectors.
Two different signals can be input at these INPUT connectors.
If two signals are input at the same time, they are mixed
before being sent to the subwoofer.
connectors.
Two different signals can be input at these INPUT connectors.
If two signals are input at the same time, they are mixed
before being sent to the subwoofer.
Do NOT use both the XLR and Phone type connector at the same
time. Please connect to only one of these connectors.
time. Please connect to only one of these connectors.
#
EXT SUB OUT connector
This is an XLR-type balanced output connector which outputs
the mixed signal received by the INPUT L/R connectors. Use
the EXT SUB OUT connector if you wish to add a second
subwoofer.
the mixed signal received by the INPUT L/R connectors. Use
the EXT SUB OUT connector if you wish to add a second
subwoofer.
n The LOW CUT switch/control and HIGH CUT control do not affect
the output level of the signal sent from the EXT SUB OUT
connector.
connector.
$
OUTPUT L/R jack
These XLR-type balanced output connectors output the
signals received at the INPUT L/R connectors, respectively. If
the LOW CUT switch is on, the low frequency is cut. Use the
LOW CUT control to set the cutoff frequency from 80 Hz to
120 Hz.
signals received at the INPUT L/R connectors, respectively. If
the LOW CUT switch is on, the low frequency is cut. Use the
LOW CUT control to set the cutoff frequency from 80 Hz to
120 Hz.
%
LOW CUT switch
If the LOW CUT switch is on, the low frequencies of the signal
from the OUTPUT connector is cut. Use the LOW CUT control
to set the cutoff frequency from 80 Hz to 120 Hz.
from the OUTPUT connector is cut. Use the LOW CUT control
to set the cutoff frequency from 80 Hz to 120 Hz.
&
LOW CUT control
Use the LOW CUT control to set the cutoff frequency from 80
Hz to 120 Hz when the LOW CUT switch is on.
Hz to 120 Hz when the LOW CUT switch is on.
'
HIGH CUT control
Use the HIGH CUT control to set the cutoff frequency of the
signal output from the HS10W from 80 Hz to 120 Hz.
signal output from the HS10W from 80 Hz to 120 Hz.
(
LEVEL control
Adjusts the overall output level.
)
PHASE switch
Selects a phase of output sound from the HS10W.
You will usually set this switch to “NORM”. However, the
“REV.” setting may improve low-range response, depending
on the type and location of the entire speaker system. Try
both settings and select the one that produces the best low-
end sound.
You will usually set this switch to “NORM”. However, the
“REV.” setting may improve low-range response, depending
on the type and location of the entire speaker system. Try
both settings and select the one that produces the best low-
end sound.
*
AC IN Connector
Connect the supplied power cable here. First connect the
power cord to the subwoofer, then insert the power cord plug
into the AC outlet.
power cord to the subwoofer, then insert the power cord plug
into the AC outlet.
L
R
L
R
L
R
OFF
OFF
L
R
0
10
80
120
100
100
80
120
INPUT
EXT
SUB
SUB
OUT
OUTPUT
HIGH
CUT
LEVEL
(Hz)
(Hz)
NORM.
REV.
INPUT
OUTPUT
EXT SUB OUT
SUBWOOFER
HIGH
CUT
PHASE
LOW CUT
LOW CUT
POWER
ON
AC IN
LOW
CUT
CUT
PHASE
ON
!
*
"
#
$
& '
(
)
%