Yamaha yst-m45d Owner's Manual
E-
8
■ Connections and setup
1. Connect the power cord (or AC adaptor) to a
suitable AC outlet.
2. Start the Macintosh.
3. Connect this unit to a USB port on the com-
puter using the supplied USB cable.
The driver software for USB audio is automati-
cally installed.
The driver software for USB audio is automati-
cally installed.
4. Press
button to turn on this unit.
Checking sound output and adjusting volume
1. Make the following operations on the front
panel of this unit.
a) Press
a) Press
button to turn on this unit.
b) Use the volume control to adjust the volume.
2. Check that the sound is output normally by out-
putting “Alert Sounds”, etc. from “Sound” on
the “Control Panels” on the Macintosh.
the “Control Panels” on the Macintosh.
3. Adjust the volume by dragging the “Sound” tab
on the “Control Panels”. Set the tab between
the center and max. position.
the center and max. position.
Note:
• The sound output destination cannot be changed
from “Choose a device for sound output” on the
“Control Panels”. When using the internal speaker
of the Macintosh as the sound output destination,
disconnect the USB cable connecting this unit and
the Macintosh.
“Control Panels”. When using the internal speaker
of the Macintosh as the sound output destination,
disconnect the USB cable connecting this unit and
the Macintosh.
• When using headphones with this unit connected
to the USB port on the Macintosh, use the head-
phone jack on this unit, not the jack on the Macin-
tosh.
phone jack on this unit, not the jack on the Macin-
tosh.
• Since the Macintosh issues a start-up sound at
power-on before the sound signal via the USB con-
nection is activated, the start-up sound cannot be
issued via the USB connection. To play the start-
up sound via this unit, you need a separate analog
connection between this unit and the Macintosh.
(When USB MIX is set to “ON” from the Setup
Panel of the Application Software, you can mix the
start-up sound via the analog connection with the
same sound via the USB connection without mak-
ing any change in the input selector settings.)
nection is activated, the start-up sound cannot be
issued via the USB connection. To play the start-
up sound via this unit, you need a separate analog
connection between this unit and the Macintosh.
(When USB MIX is set to “ON” from the Setup
Panel of the Application Software, you can mix the
start-up sound via the analog connection with the
same sound via the USB connection without mak-
ing any change in the input selector settings.)
Connecting to a non-USB system
You can input analog audio signals into Inputs 1 and 2 (3.5 mm stereo mini plug input jacks) on the rear of right
speaker and use the YST-M45D system like conventional multimedia speakers. (For example, you can connect the
outputs from a soundcard.)
speaker and use the YST-M45D system like conventional multimedia speakers. (For example, you can connect the
outputs from a soundcard.)
Some games software does not support USB. In this case, instead of using the USB connection, connect Input 1 or 2
on the rear of right speaker to the audio output jack on your computer using a 3.5 mm stereo mini plug cable, and
specify your card type. (For move information on setting, consult your computer manual or computer dealer.)
on the rear of right speaker to the audio output jack on your computer using a 3.5 mm stereo mini plug cable, and
specify your card type. (For move information on setting, consult your computer manual or computer dealer.)
Enjoying your YST-M45D Speaker System
Adjusting the Volume, Bass, and Treble
First adjust the volume levels, bass, and treble using software controls (such as the Windows 98 Volume Control
panel). After adjustment, use the VOLUME control on the right speaker to set the volume level of the speakers.
panel). After adjustment, use the VOLUME control on the right speaker to set the volume level of the speakers.
Macintosh computer