Yamaha yst-sw500 Owner's Manual
13
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
●
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
the battery compartment.)
●
Remove the batteries if the remote control transmitter will
not be used for an extended period of time.
not be used for an extended period of time.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
Remote control transmitter operation range
Notes
●
There should be no large obstacles between the remote
control transmitter and the main unit.
control transmitter and the main unit.
●
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
SYMPTOM
Power is not supplied even though the
POWER switch is ON.
POWER switch is ON.
No sound .
Sound level is too low.
The remote control transmitter does not
work.
work.
The distance or range within which the
remote control transmitter can be used
decreases.
remote control transmitter can be used
decreases.
CAUSE
The power plug is not securely connected.
The VOLUME control is set to 0.
The OUTPUT switch is OFF.
Speaker cables are not connected securely.
Speaker cables are connected incorrectly.
Setting of the PHASE switch is not proper.
A source sound with few bass frequencies is
played.
played.
It is influenced by the standing waves.
Direct sunlight or lighting (of an inverter type
of flourescent lamp etc.) is striking the
remote control sensor of the main unit.
of flourescent lamp etc.) is striking the
remote control sensor of the main unit.
The batteries of this remote control
transmitter are too weak.
transmitter are too weak.
REMEDY
Connect it securely.
Turn the VOLUME control to right.
Press the OUTPUT switch so that the
OUTPUT indicator on the front panel
illuminates.
OUTPUT indicator on the front panel
illuminates.
Connect them securely.
Connect them correctly, that is to say L (left)
to L, R (right) to R, “+” to “+” and “–” to “–”.
to L, R (right) to R, “+” to “+” and “–” to “–”.
Set the switch to the other position.
Play a source sound with bass frequencies.
Set the HIGH-CUT control to a higher
position. (Turn the knob to right.)
Set the HIGH-CUT control to a higher
position. (Turn the knob to right.)
Break up the parallel surface by placing
bookshelves etc. along the walls.
bookshelves etc. along the walls.
Change position of the main unit.
Replace the batteries with new ones.
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
TROUBLESHOOTING
30
°
30
°
Remote control
senser
senser
Within approximately
7mm (23 feet)
7mm (23 feet)