Sonance BPS-1 Specification Guide

BPS-1 BANDPASS SUBWOOFER

BPS-1

Specifi cations

Woofer:

8” (203mm) long-throw felted
paper cone with a rubber
surround

Frequency Response:

35Hz – 150Hz ±3dB

Enclosure Dimensions:

9” x 11” x 39½”

(W x H x D)

(229mm x 279mm x 1283mm)

Port Tube Length:

15”

(381mm)

Minimum Mounting Area:

” x 11” x 53¼”

(W x H x D)

(232mm x 279mm x 1352mm)

Shipping Weight:

46 lbs (20.9kg) each

SONANCE BPS-1 BANDPASS SUBWOOFER

The Sonance Architectural Series

BPS-1 Bandpass Subwoofer

system will add deep, powerful bass impact to any audio system.

The

BPS-1

cabinet remains completely hidden from view, delivering its bass energy through Sonance Architectural Series

brackets and an architectural fi nish component that is a discreet complement to the surrounding architectural space.

Features

• Delivers powerful, room-fi lling bass through a small grille that complements the room’s architectural design.
• Trimless and truly fl ush-mount installation — the plane of the subwoofer grille is perfectly aligned with the plane of the ceiling.
• Required Bandpass Connectors allow the

BPS-1

to be used with any size round or square Architectural Series bracket to match other Architectural

Series speakers in the space. The Bandpass Connectors are heavily fl ared to minimize port noise during high-volume passages.

• Engineered to provide years of reliable high-power operation, the

BPS-1

features a woofer with a felted paper cone with a rubber surround. The

required Sonamp

A150 is designed to protect the speaker from damage. This ensures the

BPS-1

can be installed in a location that will have limited

or no access without the need for maintenance.

• The very effi cient 4th-order bandpass enclosure produces high output over the subwoofer’s entire frequency range.
• The

BPS-1

can be used with any separately-available Architectural Series round and square fi nish component: metal (with or without trim) or cloth

(with or without trim).

Sonance

212 Avenida Fabricante
San Clemente, CA 92672-7531 USA
1.800.582.7777
sonance.com

©2008 Sonance, All Rights Reserved. Sonance, Sonance Architectural Series, and Sonamp are registered trademarks of Dana Innovations.
Due to continuous product improvement, all features and specifications are subject to change without notice. For the latest Sonance product information, go to : www.sonance.com

SONAMP A150 AMPLIFIER

(required, available separately)

•

Sonamp A150

power amplifi er delivers 150 watts of power to up to two

BPS-1

subwoofers and provides fl exible connections that integrate the

BPS-1

into any audio system.

• A built-in limiter prevents overdriving the

BPS-1

’s woofer driver, even when using a single

Sonamp A150

to drive two

BPS-1

subwoofer cabinets.

• The

A150

’s front-panel amplifi er controls (volume, crossover frequency, and phase) let you fi ne-tune the

BPS-1

’s performance to match a variety of listening

environments and personal preferences.

Sonamp A150

Specifi cations

Maximum Continuous RMS Power
at Clipping:

watts

Power Output (Program):

150 watts

Signal-to-Noise Ratio:

–95dB

Auto-On Trigger Sensitivity:

10mV

Low-Pass Crossover Frequency:

40Hz ~ 150Hz (variable),

(Bypass Switch OFF)

12dB/octave

Low-Pass Crossover Frequency:

150Hz

(fi xed), 12dB/octave

(Bypass Switch ON)
Hi Level Out Hi-Pass Filter:

–3dB @ 200Hz, 6dB/octave

Line Level Out Hi-Pass Filter:

–3dB @ 150Hz, 6dB/octave

Controls:

Variable crossover frequency, variable
output level, Phase switch, Bypass
switch

Power Consumption:

13w (idle); 160w (max power)

Dimensions (W x H x D):

16¾” x 4” x 13½”
(425mm x 102mm x 343mm)

Shipping Weight:

20 lbs (9.1kg) each

GAP

2 X 10

JOIST

9-1/8”

(232mm)

MINIMUM

MOUNTING

HEIGHT

GYPSUM

WALL BOARD

11” (279mm)

1/8”

(3mm)

39-1/2” (1003mm)

15” (381mm)

53-1/4” (1353mm)

Minimum Mounting

Area Dimensions

33-5164