Sonance mariner 51 User Guide

Page of 4
8. Fit the wiring connector cover into the recess in the speaker’s front
panel. The cover should fit tightly, but can be removed and replaced if
the speaker needs to be disconnected.
9. Fit the grille onto the speaker.
• The Sonance logo can be removed, rotated 90° and replaced in its
centering dimple. This maintains the correct logo orientation on a
speaker that is mounted vertically.
10. If you’re placing the speaker on a shelf without using the bracket,
attach the 2 plastic inserts to the speaker’s top and bottom ends so
they snap into place.
• If you wish to mount the speaker on its bracket at a later time you can
remove the inserts by pulling-down the tabs behind the grille.
Note: All Sonance Mariner speakers are compatible with Omnimount 20.5
Series speaker brackets. The 20.5 series includes several different mounts
that accommodate a wide range of different mounting requirements. For
more information contact your Sonance Authorized dealer or go to
www.omnimount.com.
PIVOTING THE SPEAKER
You can rotate the speaker in the bracket
to direct the sound towards the listeners.
1. Unlock the slide locks on the
speaker pivots by moving
them towards the rear of the
speaker.
2. Rotate the speakers to the
desired position.
3. Lock the slide locks by mov-
ing them towards the front
of the speaker.
PAINTING THE SPEAKER AND GRILLE
All Mariner speakers feature a tough polypropylene enclosure that can
be painted. Sonance recommends using a weather-resistant outdoor
paint and a spray gun to paint the Mariner speakers.
1. If it has already been installed, remove the grille from the speaker.
2. To protect the speaker driver units during painting, place the grille on
a piece of cardboard and trace around its outline. Then cut the card-
board just inside of the trace line and fit this “paint plug” into the
speaker’s baffle. (Be careful not to damage the driver components
while fitting the paint plug.)
3. Paint the speaker the desired color according to the paint
manufacturer’s instructions. Remove the paint plug after the paint has
thoroughly dried.
4. Remove the Sonance logo before painting the grille. Paint the grille
separately from the speaker using very thin paint (5:1 thinner:paint
ratio). Avoid plugging the grille holes with excess paint.
5. After the paint has thoroughly dried, re-attach the Sonance logo
to the grille and attach the grille to the speaker.
SPECIFICATIONS
Mariner 82
Tweeter:
1” (25mm) Polyurethane dome
Woofer:
8” (203mm) One-piece black Polypropylene cone with a
rubber surround
Frequency Response:
45Hz – 20kHz  ±3dB
Impedance:
6 ohms nominal; 4 ohms minimum
Power Handling:
5 watts minimum; 125 watts maximum 
Sensitivity:
91dB SPL (2.83V/1 meter)
Grille Material:
Perforated aluminum
Dimensions (H x W x D):
14” x 9” x 9¼” (356mm x 229mm x 235mm)
Shipping Weight:
20 lbs (9.0 KG) per pair
Mariner 63
Tweeter:
1” (25mm) Aluminum dome
Woofer:
6½” (165mm) One-piece black Carbon Fiber cone with a
rubber surround
Frequency Response:
50Hz – 20kHz  ±3dB
Impedance:
6 ohms nominal; 4 ohms minimum
Power Handling:
5 watts minimum; 100 watts maximum 
Sensitivity:
90dB SPL (2.83V/1 meter)
Grille Material:
Perforated aluminum
Dimensions (H x W x D):
12” x 7½” x 7
1
/
8
” (305mm x 191mm x 181mm)
Shipping Weight:
17 lbs (7.7 KG) per pair
Mariner 62
Tweeter:
1” (25mm) Polyurethane dome
Woofer:
6½” (165mm) One-piece black Polypropylene cone with
a rubber surround
Frequency Response:
55Hz – 20kHz  ±3dB
Impedance:
8 ohms nominal; 6 ohms minimum
Power Handling:
5 watts minimum; 80 watts maximum 
Sensitivity:
89dB SPL (2.83V/1 meter)
Grille Material:
Perforated aluminum
Dimensions (H x W x D):
12” x 7½” x 7
1
/
8
” (305mm x 191mm x 181mm)
Shipping Weight:
14 lbs (6.4 KG) per pair
Mariner 61
Tweeter:
¾” (19mm) Polyurethane dome
Woofer:
6½” (165mm) One-piece black Polypropylene cone with
a rubber surround
Frequency Response:
60Hz – 20kHz  ±3dB
Impedance:
8 ohms nominal; 6 ohms minimum
Power Handling:
5 watts minimum; 80 watts maximum 
Sensitivity:
88dB SPL (2.83V/1 meter)
Grille Material:
Perforated aluminum
Dimensions (H x W x D):
12” x 7½” x 7
1
/
8
” (305mm x 191mm x 181mm)
Shipping Weight:
12.5 lbs (5.7 KG) per pair
continued on back
3
8. Attach the 
connector cover
9. Attach 
the grille
UNLOCK
(towards rear
of speaker)
LOCK
(towards front
of speaker)
I N S T R U C T I O N   M A N U A L
S O N A N C E   L A N D S C A P E   S E R I E S
M A R I N E R
®
O U T D O O R   S P E A K E R S