Sonance vp67lcr User Guide
3
SONANCE VISUAL PERFORMANCE VP67LCR
N
O T E
: T
H E
F
A S T
M
O U N T TA B S A R E D E S I G N E D F O R O N E
-
T I M E U S E
O N LY
. I
F T H E S P E A K E R I S R E M O V E D F R O M T H E M O U N T I N G H O L E
T H E
F
A S T
M
O U N T TA B S W I L L D I S C O N N E C T A N D R E M A I N I N S I D E
T H E WA L L
.
6. Tighten the four screws on the front of the speaker baffle. The
RotoLock clamps will automatically rotate into position and
begin clamping the speaker (see
begin clamping the speaker (see
Figure 5 right).
• When you notice resistance on the screws the speaker has
been clamped successfully.
IMPORTANT: Always use low-torque settings;
never over-tighten.
never over-tighten.
N
OTE
: A
DJUSTING THE TENSION OF THE
R
OTO
L
OCK CLAMPS SO
THAT THE SPEAKER FRAME IS FLAT WILL HELP ENSURE THAT THE
GRILLE CONTACTS THE WALL ALL THE WAY AROUND THE SPEAKER
FOR A PROPER FIT
.
7. The new micro flange grille is held in place by several small,
powerful magnets on the speaker frame. Place the grille
against the speaker and the magnets will hold it firmly in
place. When properly installed, the grille flange should make
contact with the wall all the way around the speaker.
against the speaker and the magnets will hold it firmly in
place. When properly installed, the grille flange should make
contact with the wall all the way around the speaker.
Painting The Grilles
Please see the accompanying
Painting Instructions sheet for
painting instructions.
Adjustments
Tweeter Level Control
The VP67LCR has a tweeter
level control switch
(see
Figure 6) that boosts or cuts the tweeter’s level by 3dB.
This lets you adjust the speaker’s sound to better match the
listening room or your personal taste.
listening room or your personal taste.
Once you have installed the speakers, listen to a variety of music
that you are familiar with. If the music all tends to sound too
that you are familiar with. If the music all tends to sound too
bright or dull, use the Tweeter Level Control to compensate. If
some recordings sound dull and some sound bright the speaker
is accurately reproducing differences in the recordings, and you
should leave the control in the middle (0dB) position.
some recordings sound dull and some sound bright the speaker
is accurately reproducing differences in the recordings, and you
should leave the control in the middle (0dB) position.
Specifications
VP67LCR
Tweeter:
1”
(25mm) Aluminum dome,
Ferrofluid-cooled
Woofer:
Two 6½” (165mm) Coated carbon
fiber cones, rubber surround
fiber cones, rubber surround
Frequency Response:
43Hz – 20kHz ±3dB
Impedance:
6 ohms nominal; 4 ohms minimum
Power Handling:
5 watts minimum;
140 Watts maximum
140 Watts maximum
Sensitivity:
90dB SPL (2.83V/1 meter)
Grille Material:
Perforated Steel
Adjustments:
±3dB tweeter level
Grille Dimensions (W x H): 16” x 8
3
/
8
” (406mm x 213mm)
Mounting Depth:
3
9
/
16
” (91mm)
Cutout Dim (W x H):
6
7
/
8
” x 14
5
/
8
” (175mm x 371mm)
Shipping Weight:
8 lbs. (3.6kg) Each
T
WEETER
L
EVEL
C
ONTROL
F
I G U R E
6 : T
W E E T E R
L
E V E L
C
O N T R O L
RotoLock Clamps
Retracted
FastMount
Tabs
RotoLock Clamps
Extended
F
I G U R E
5 : T
I G H T E N I N G T H E
R
O T O
L
O C K
C
L A M P S