JVC gr-axm240 Instruction Manual

To magnify the recorded image up to 10X at any
time during playback. Make sure that the TBC
mode is activated.

1) Press PLAY 

T

 to find the scene of interest.

2) Press ZOOM (T/W) 

R

. Pressing T zooms in. To

end zoom press and hold W until magnification
returns to normal. Or, press STOP 

U

 and then

press PLAY 

T

.

• Due to digital image processing, the quality of the

image may suffer.

The remote control lets you set/release interval
time and recording time without setting REC TIME/
INT. TIME (

 pg. 21) in SYSTEM MENU.

Animation
Each time ANIM. 

O

 is pressed, the recording time

changes in the following order: 1/4S, 1/2S, 1S, 5S
and no indication (off).

Time-Lapse
Each time REC TIME 

O

 is pressed, the recording

time changes in the following order: 1/4S, 1/2S,
1S, 5S and no indication (off). Each time INT. TIME

f

 is pressed, the interval time changes in the

following order: 15S, 30S, 1MIN, 5MIN and no
indication (off).

You can record a new scene onto a previously
recorded tape. Only the video signal is recorded in
this mode.
1) Set the Power Switch 

@

 to “

”.

2) Play back the tape, locate the edit-out point and

press PAUSE 

s

.

 

Press and hold COUNTER R/M

)

 for more than 1 second to reset the tape

counter, then press it again for less than
1 second so that “M” appears.

3) Press REW 

Y

 to go a little beyond the beginning

of the scene you want to replace, press PLAY 

T

to view the recorded tape, and press PAUSE 

s

exactly at the edit-in point where the new scene
should start.

4) While holding down INSERT 

I

, press and

release PAUSE 

s

. w appears.

5) To begin Insert Editing, press START/STOP 

P

.

When the counter reaches “0:00:00”, editing
stops automatically and the camcorder enters
the Insert-Pause mode. To end Insert Editing,
press STOP 

U

.

• During Insert Editing, the original audio will be

heard from the speaker.

• After step 4), “Retake” (

 pg. 13) can be

performed.

• The tape may stop slightly before or after the

designated end point, and noise bars may appear.
Neither indicates a defect in the unit.

You can record a new soundtrack on a
prerecorded tape (normal audio only). The sound
is recorded from the built-in microphone.

Perform steps 1) and 2) of the Insert Editing
procedure.

3) Press REW 

Y

 to go a little beyond the beginning

of the scene onto which you want to dub the new
audio, press PLAY 

T

 to view the recorded tape,

then press PAUSE 

s

 at exactly the point where

dubbing should start.

4) While holding down A. DUB 

d

, press and

release PAUSE 

s

.

5) To begin Audio Dubbing, press PLAY 

T

. When

the counter reaches “0:00:00”, Audio Dubbing
stops automatically and the camcorder enters
the Audio Dub-Standby mode. To end Audio
Dubbing, press STOP 

U

.

• Do not press REW 

Y

 or FF 

a

 during Audio Dub-

Standby, or the edit points will not be accurate.

• If the microphone is too close to the TV, or if the

TV’s volume is too high, whistling or howling may
occur.

For Insert Editing/Audio Dubbing
• Insert Editing and Audio Dubbing may not work

correctly if the tape contains blank segments, or if
the recording speed was changed during the
original recording.

• To edit/dub onto a tape, make sure the erase

protection tab is in the position that allows
recording.

• Do not press STOP 

U

 during Insert Editing or

Audio Dubbing, or the edit points will not be
accurate.

Make sure the remote control is pointed at the remote sensor 

p

.