Sony kdl-46xbr6 Quick Setup Guide

KDL-40/46/52XBR6/KDL-52XBR7 EN 4-113-761-12(1)

VIDEO

OUT

COMPONENT

VIDEO OUT

DIGITAL OUT

PCM/DTS/DOLBY DIGITAL

5.1CH OUTPUT

VIDEO

Y

L

R

AUDIO

OUT

L

R

WOOFER

COAXIAL

OPTICAL

FRONT

REAR

CENTER

S VIDEO

HDMI

OUT

AC IN

PB/CB

PR/CR

OPT IN

SAT

OPT IN

VIDEO 1

COAX IN

AUDIO IN

DVD

DVD IN

SAT IN

VIDEO 2/BD IN

OUT

AUDIO IN

AUDIO IN

FRONT R

AM

FRONT L

SUR R

SUR L

CENTER SUBWOOFER

Your TV is equipped with four HDMI inputs and two component inputs. Connect 

your incoming signal source (HD Cable Box, HD Satellite Receiver, or DVD) with 

HDMI or component video for the best possible picture quality.

If your connecting equipment has DVI output instead of the HDMI output, you must 

use a DVI-to-HDMI cable for the video and also connect an audio cable for the 

sound. If this is the case, connect the cable to HDMI IN 4 (input) of your TV.

■

■

When using a DVI-to-HDMI cable, make sure to connect the DVI side first.

P&P/PIP functions require Cable/Antenna connection.

When receiving a High-Definition signal by an over-the-air antenna, it is best to use 

an HD antenna.  

■

■

■

HD Antenna

Cable/SAT 

(dish)

SD Cable Box or 

SD Satellite Receiver

Home Theater System

or

Coaxial

HDMI

DVI-to-HDMI

Component

Composite

Audio (L/R)

Mini-Pin Audio

Digital Optical Audio

Audio (L/R) with Mini-Pin

HD15

DVI - to - HDMI 

adapter

Blu-ray Disc/DVD

Cable/Antenna

Notebook PC

Splitter

SAT 

(dish)

HD Cable Box or 

HD Satellite Receiver

Rear of TV

Rear of TV

Cable/Antenna

A/V Receiver

Splitter

Blu-ray Disc/DVD

SAT  

(dish)

HD Cable Box 

or HD Satellite 

Receiver

Rear of TV

Cable/Antenna

*A/V Receiver

*Blu-ray Disc

SAT  

(dish)

HD Cable Box  

or HD Satellite 

Receiver

*Rear of TV

Splitter

Cable/Antenna

Splitter

Rear of TV

VCR/DVD Combo

VCR

DVD

* Signifies a BRAVIA Sync capable device.

DVD

DVD Player

31033

AMP

Receiver

52172

STB

Digital Satellite

01639

Follow the steps below to program your TV remote control. 

  

Look for the code in the Manufacturer’s Codes List (see Operating Instructions Manual) 

that corresponds to the equipment you would like to operate with the Sony remote control. 

If more than one code is provided, try programming the first code listed. If your equipment’s 

code is not listed, visit http://esupport.sony.com/remotecodes for a more comprehensive list. 

  

Press and hold 

, 

 or 

 simultaneously with the 

 button and release. 

When in the programming mode, the FUNCTION button blinks for approximately  

30 seconds until a code is entered.  

  

Enter the five digit code using  –  while the FUNCTION button is lit. If the code is not 

entered within 30 seconds, you must repeat step 2.

 

 Press   or   to confirm the code. If successfully programmed, the FUNCTION button 

will blink twice, if not, it blinks five times.

If you can turn your equipment on and off using the green 

POWER

 button, the programming is 

complete. If not, try the next code listed. 
Note:

In some cases, you may not be able to program your remote control. If this is the case, use 

your equipment’s remote control.

 

Any of the FUNCTION buttons can be programmed to operate other equipment regardless 

of the labeling. For example, if programmed with the correct code, a Blu-ray Disc player 

can be operated with the 

 button. This is useful if your equipment does not match any 

of the labeled buttons.

■
■

PC

DVD

AMP

STB

TV