Delfield F18RC52 Specification Guide
Optional Accessories & Modifications
906A
Stainless steel end
505H
Stainless steel back
505F
Laminate facing (full front)
906E
Laminate end
905A
Laminate back
1030A Cutting board (Sanalite or composite)
107F
107F
Tray rack
1027A Casters
102
102
Drawers
A-(2) 19” in lieu of one door
B-(2) 27” in lieu of one door
C-(2) 32” in lieu of one door
B-(2) 27” in lieu of one door
C-(2) 32” in lieu of one door
108
Locks
120F
Cold pan drain
213
*220V/50 cycle
*Inclusion of this option will alter the
electrical specifications of the unit
Short Form Specifications
Exterior top is one-piece, 16-gauge stainless steel, with integral 2.12”
(5.4cm) high square nosing on front. Top has a mechanically cooled refrigerat-
ed raised rail at rear with openings to accommodate 1/6 size pans. Pans and
adapter bars are provided by others. Pans are recessed 3” (7.6cm) or 2”
(5.1cm) and set on adjustable stainless steel pan supports. Rail interior is 22-
gauge stainless steel. Raised rail openings have 20-gauge stainless steel remov-
able lids. Unit is equipped with separate expansion valve and on/off switch for
refrigerated cold pan. Temperature in top opening to maintain 33°F (1°C) to
41°F (5°C) with pans recessed 3” (7.6cm) at 86° ambient room temperature,
meeting NSF7 requirements.
(5.4cm) high square nosing on front. Top has a mechanically cooled refrigerat-
ed raised rail at rear with openings to accommodate 1/6 size pans. Pans and
adapter bars are provided by others. Pans are recessed 3” (7.6cm) or 2”
(5.1cm) and set on adjustable stainless steel pan supports. Rail interior is 22-
gauge stainless steel. Raised rail openings have 20-gauge stainless steel remov-
able lids. Unit is equipped with separate expansion valve and on/off switch for
refrigerated cold pan. Temperature in top opening to maintain 33°F (1°C) to
41°F (5°C) with pans recessed 3” (7.6cm) at 86° ambient room temperature,
meeting NSF7 requirements.
Exterior Back and Bottom are 24-gauge galvanized steel. Exterior ends are
finished with 18-gauge galvanized steel.
finished with 18-gauge galvanized steel.
Base Interior has 22-gauge stainless steel back and bottom. Base interior
ends and door frames are thermoformed ABS plastic. Base is insulated with
1.5” (3.8cm) high density foamed in place polyurethane. End of base has a
machine compartment, standard on right, with condensing unit installed.
ends and door frames are thermoformed ABS plastic. Base is insulated with
1.5” (3.8cm) high density foamed in place polyurethane. End of base has a
machine compartment, standard on right, with condensing unit installed.
Door(s) have a 22-gauge stainless steel exterior front, with thermoformed
ABS plastic interior liner, black recessed handle and snap in magnetic gasket
which is easily replaceable. Each interior door section has (1) removable
epoxy coated wire shelf.
ABS plastic interior liner, black recessed handle and snap in magnetic gasket
which is easily replaceable. Each interior door section has (1) removable
epoxy coated wire shelf.
Refrigeration System uses HFC-404A refrigerant. Cabinet has a blower coil
assembly with expansion valve located behind door mullion. Base is equipped
with independently controlled thermostat, solenoid valve and condensate
evaporator. On/off switch for unit is located on panel above louver.
Refrigeration system in the base will maintain 36°F (2°C) to 40°F (4°C).
assembly with expansion valve located behind door mullion. Base is equipped
with independently controlled thermostat, solenoid valve and condensate
evaporator. On/off switch for unit is located on panel above louver.
Refrigeration system in the base will maintain 36°F (2°C) to 40°F (4°C).
Unit is mounted on 6.13” (15.6cm) high adjustable stainless steel legs.
Electrical connections are 115 volt, 60 Hertz, single phase. Unit is wired
with 8’ (2.4m) cord and plug.
with 8’ (2.4m) cord and plug.
Model F18RC91
31.5” (80cm) Deep Self-Contained Refrigerated Reduced Height Rail
The Delfield Company, P.O. Box 470, Mt Pleasant, MI 48804-0470, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2001 The Delfield Company. All rights reserved. Printed in U.S.A.
PROJECT
ITEM #
QUANTITY
DATE
APPROVAL
F18RC
®