Ricoh ap900 Supplementary Manual
Troubleshooting
89
Add staples
(Booklet: Back)
The back stapler of the
Booklet Finisher is out of
staples.
Booklet Finisher is out of
staples.
Add staples to the back stapler of the
Booklet Finisher.
Booklet Finisher.
See
Alternatively, cancel staple mode us-
ing {Form Feed}, or cancel the job.
ing {Form Feed}, or cancel the job.
Add staples
(Booklet: Front)
The front stapler of the
Booklet Finisher is out of
staples.
Booklet Finisher is out of
staples.
Add staples to the front stapler of the
Booklet Finisher.
Booklet Finisher.
See
Alternatively, cancel staple mode us-
ing {Form Feed}, or cancel the job.
ing {Form Feed}, or cancel the job.
Add Toner
The printer is out of toner.
Replace the toner bottle.
See
Call Service: EC
Power Off On
Call Service if
error reoccurs
A communication error
was sent from the engine
to the controller.
was sent from the engine
to the controller.
Turn the power switch to Standby,
and then to ON. If the message ap-
pears again, call your service provid-
er.
and then to ON. If the message ap-
pears again, call your service provid-
er.
Cannot check
Signal in Ad hoc
An attempt to check the ra-
dio signal was made while
the communication mode
was set to [802.11 Ad hoc] in
the Maintenance menu.
dio signal was made while
the communication mode
was set to [802.11 Ad hoc] in
the Maintenance menu.
To check the radio signal , select In-
frastructure in the communication
mode settings.
frastructure in the communication
mode settings.
Cannot duplex
Tray #
The selected tray is set to
1 sided tray when duplex
mode is set.
1 sided tray when duplex
mode is set.
Cancel duplex mode. Alternatively,
select another tray using {Form
Feed}, or cancel the job.
select another tray using {Form
Feed}, or cancel the job.
Cannot select
same Tray for:
Cannot print because
main sheets and designa-
tion sheets are set to the
same tray.
main sheets and designa-
tion sheets are set to the
same tray.
Press the {Reset} key.
Cancel the job and change the set-
ting for the Main sheet tray and des-
ignation sheet tray, and then try
printing the job again.
ting for the Main sheet tray and des-
ignation sheet tray, and then try
printing the job again.
Change Setting
Tray#
The printer detected that
the user-specified paper
type is not the same as the
paper type specified in the
driver.
the user-specified paper
type is not the same as the
paper type specified in the
driver.
Load the indicated tray with the cor-
rect paper, or change the paper type
using the Paper Type menu on the
operation panel. Alternatively, select
another tray using {Form Feed}, or
cancel the job.
rect paper, or change the paper type
using the Paper Type menu on the
operation panel. Alternatively, select
another tray using {Form Feed}, or
cancel the job.
Change Setting
Tray#
Paper Size:
Paper Type:
The printer detected that
the actual paper type and
size are not the same as
the paper tray size and pa-
per type setting.
the actual paper type and
size are not the same as
the paper tray size and pa-
per type setting.
Load the indicated tray with the cor-
rect paper, or change the paper
type/size using the dial or using the
Paper Input menu on the operation
panel. Alternatively, select another
tray using {Form Feed}, or cancel the
job
rect paper, or change the paper
type/size using the dial or using the
Paper Input menu on the operation
panel. Alternatively, select another
tray using {Form Feed}, or cancel the
job
Messages/Second mes-
sages
sages
Causes
Solutions