Lindy KVM over IP Access Switch Classic 39415 Leaflet
Product codes
39415
Page 4
When opened your browser will display the following page with the remote console window on
the right.
To launch the Remote Console click on the
Console icon –
Remote Console
Starting the Remote Console opens an
additional window. It displays the screen
content of your host system. The Remote
Console will behave in exactly the same
way as if you were sitting directly in front of
the screen of your host system. However,
be aware of the fact that the host system
will react to keyboard and mouse actions
with a slight delay depending on the
bandwidth of the connection.
Therefore a double mouse cursor mode
can be used showing both the local and
the remote cursor in parallel.
The upper part of the Remote Console
window contains a control bar. Using its
elements you can see the state of the
Remote Console and influence the local
Remote Console settings. There are
several options to choose from, below is an
introduction to the most important ones.
Please refer to the User Manual for further
options and information.
Commands like CTRL+ALT+DEL are
always interpreted from the local computer and therefore must be sent by a button from the
control bar or from a dedicated command tool.
Auto Adjust button
If the video display is poor quality or distorted in some way, click this button and wait a few
seconds while the IP Access Switch adjusts itself for the best possible video quality.
Sync mouse
Choose this option in order to synchronize the local and remote mouse cursors. If the mouse
does not synchronize, select Intelligent Sync from the Mouse Handling sub menu of the
Remote Console Option menu.
Video Settings (from within the Options Menu)
This opens a new window from which you can adjust brightness, contrast etc. of the displayed
picture in the Remote Console window.
Quick Installation is now complete. Refer to the full User Manual on the supplied CD for
more information about the advanced features of the KVM over IP Access Module!
IP Access KVM Switch Classic Quick Start Guide
Tested to comply with FCC Standards. For commercial use only.
Page 1
Package Contents
Introduction:
The IP Access Switch provides remote KVM over IP access to a computer or KVM switch. It
converts all keyboard video and mouse signals and sends them as TCP/IP signals over your
LAN/WAN connection. The remote computer or KVM switch may be accessed from any
computer connected to your network (or via RS232 port and an external modem to a telephone
line) and provides full KVM access including BIOS level access to all the connected computers.
The IP Access Switch can be accessed via a web browser and via dedicated software tools
included with the product. It uses secure encrypted sessions and password authentification.
Please note that KVM over IP does not operate in a “real time” environment and that some
degree of time delay will occur due to limiting factors such as available bandwidth and network
traffic.
Installation:
Before you install the IP Access switch ensure all connected devices are switched off and the
power supply is unplugged. The IP Access Switch is installed in between your computer or KVM
switch and its console. Use the supplied 3in1 KVM combo cable to connect the computer or
KVM switch to the IP Access Switch ports labeled PC/ KVM switch. Connect your local console
monitor, mouse and keyboard to the ports labeled Console. If you wish to use the USB Virtual
Storage feature, then connect the supplied USB cable to your computer and the IP Access
Switch. Connect the IP Access Switch to your network via RJ45 cable or to an external modem
via RS232 cable and reconnect the power supply.
Configuration
By factory default, the IP Access Switch is
configured to a fixed IP. It is recommended
that you configure a fixed IP assignment to
the MAC address. You can find the units
specific MAC address details on the printed label on the underside of the IP Access module.
Use the configuration tool PSETUP included on the supplied CD to change the network settings
of the IP Access Switch.
Parameter
Value
IP auto configuration
none
IP-Address
192.168.0.70
Net-mask
255.255.255.0
Default-Gateway
None
IP Access KVM Switch Classic
Rubber feet & 19” rack mount kit
Power supply 100…240VAC / 5VDC
RS232 Serial cable
KVM combo cable PS/2 & VGA
USB A to Mini-B Cable, 1m
Software & User Manual CD
This Quick Start Guide
This Quick Start Guide provides a brief introduction to the IP Access KVM Switch
Classic and shows you how to quickly set up the device for use. For more detailed
operation instructions please consult the full User Manual on the supplied CD.