Scitec aegis-t User Manual
[FLASH] is used to access PBX system features, like “system hold,”
“transfer/conference,” or “call park.” Pressing [FLASH] has the same
effect as “tapping” the hookswitch. The standard flash time is 600msec.
[FLASH] may be stored in programmable speed-dial memory keys, along
with other digits. Please see your PBX system manual for additional
information and exact digit sequences required for accessing special PBX
system features.
[REDIAL] redials the last number dialed
,
up to 16 digits total. It is not
necessary to hang up first before pressing [REDIAL], as pressing
[REDIAL] automatically hangs up for one second before redialing begins.
[REDIAL] automatically hangs up for one second before redialing begins.
Ringer volume:
The ringer volume switch is located at rear of
telephone.
Positions: LO
- HI.
“LO” ringer volume setting is
recommended for most users. If the telephone is installed in a very noisy
location, the “HI” ringer volume setting may be preferred.
location, the “HI” ringer volume setting may be preferred.
Speed-Dial Key Programming
1. Before programming speed-dial keys, the telephone must be plugged
into an active telephone line. Then lift the handset, or press the
speakerphone key to take telephone “off-hook.”
speakerphone key to take telephone “off-hook.”
2. Remove the faceplate from the phone.
3. Press the [STORE] key.
4. Dial the desired phone number to be stored. Include [PAUSE] or
3. Press the [STORE] key.
4. Dial the desired phone number to be stored. Include [PAUSE] or
[FLASH] when necessary. There is a 16 digit storage capacity for
each memory key.
each memory key.
Note – The [PAUSE] key will insert a 3.6 second pause before
the next number is dialed out. If a “9” prefix (or any other digit) is required
to access an outside telephone line, then a “pause” might be required
after the first number dialed. For example: 9 [PAUSE] 1 – 800 – 555 –
1212. A pause may also be required when accessing voice mail systems,
between dialing the voice mail system access number and entering the
user’s passcode.
5. Press the speed-dial key in which the number is to be stored.
6. To continue programming more keys, repeat steps 3-5. It is not
to access an outside telephone line, then a “pause” might be required
after the first number dialed. For example: 9 [PAUSE] 1 – 800 – 555 –
1212. A pause may also be required when accessing voice mail systems,
between dialing the voice mail system access number and entering the
user’s passcode.
5. Press the speed-dial key in which the number is to be stored.
6. To continue programming more keys, repeat steps 3-5. It is not
necessary to hang up first or obtain a new dial tone before continuing
with programming.
with programming.
Note - Speed-dial memory key contents are retained even if telephone is
unplugged from an active telephone line.
unplugged from an active telephone line.
Dataport:
The jack on the right side of the telephone (labeled DATA), next
to the speaker volume control, may optionally be used to connect a
computer modem, credit card terminal, or other similar accessory device
directly to telephone line. Any device plugged into the dataport will utilize
Line 2 when taken “off-hook”. Note that the telephone and device
plugged into the DATA jack cannot both be “off-hook” at the same time,
as both ports share the same telephone line.
computer modem, credit card terminal, or other similar accessory device
directly to telephone line. Any device plugged into the dataport will utilize
Line 2 when taken “off-hook”. Note that the telephone and device
plugged into the DATA jack cannot both be “off-hook” at the same time,
as both ports share the same telephone line.
Do not attempt to use Dataport for connecting the handset,
headset, or for connecting telephone to PBX. The dataport is ONLY
for connecting computer modems or similar accessory devices.
for connecting computer modems or similar accessory devices.
Required FCC Notice:
This equipment complies with Part 68 of the FCC rules and the
requirements adopted by the ACTA. On the bottom of this equipment is a
label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, this number must be provided
to the telephone company.
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line may
result in the devices not ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone company. The
REN for this telephone is part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are the REN without
a decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of
service may be required. If advance notice isn't practical, the Telephone
Company will notify you as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment,
operations, or procedures that could affect the operation of this telephone.
If this happens, the Telephone Company will provide advance notice in
requirements adopted by the ACTA. On the bottom of this equipment is a
label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, this number must be provided
to the telephone company.
The REN is used to determine the number of devices that may be
connected to a telephone line. Excessive RENs on a telephone line may
result in the devices not ringing in response to an incoming call. In most
but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as
determined by the total RENs, contact the local telephone company. The
REN for this telephone is part of the product identifier that has the format
US:AAAEQ##TXXXX. The digits represented by ## are the REN without
a decimal point (e.g., 03 is a REN of 0.3).
If this equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of
service may be required. If advance notice isn't practical, the Telephone
Company will notify you as soon as possible. Also, you will be advised of
your right to file a complaint with the FCC if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment,
operations, or procedures that could affect the operation of this telephone.
If this happens, the Telephone Company will provide advance notice in