Aiwa av-d67 User Guide
19
ENGLISH
SETTING THE SLEEP TIMER
TIMER
SETTING THE CLOCK
When the AC cord is connected for the first time, the clock on
the display flashes.
Set the time as follows while the power is off.
the display flashes.
Set the time as follows while the power is off.
1 Press the ENTER button.
The display becomes a little brighter.
2 Within 4 seconds, turn the MULTI JOG to
designate the hour and the minute.
The time advances by turning it to the right, and decreases
by turning it to the left.
The
by turning it to the left.
The
N
or
M
button on the main unit is also available. Press
the button repeatedly. To change the time rapidly in 10-minute
steps, hold it down.
steps, hold it down.
3 Press the ENTER button.
The clock starts from 00 seconds.
NOTE
When the clock is set for the first time after purchase
Everything on the display will clear.
This is because the power economizing mode of the unit is
activated, and is not a malfunction.
The power economizing mode can be canceled. See page 7 for
details.
Everything on the display will clear.
This is because the power economizing mode of the unit is
activated, and is not a malfunction.
The power economizing mode can be canceled. See page 7 for
details.
To correct the current time
Press the POWER button to turn the unit off. Carry out steps 1
to 3 above.
Press the POWER button to turn the unit off. Carry out steps 1
to 3 above.
To display the current time
Press the CLOCK button while pressing the SHIFT button on
the remote control. The clock is displayed for 4 seconds.
Press the CLOCK button while pressing the SHIFT button on
the remote control. The clock is displayed for 4 seconds.
To switch to the 24-hour standard
Display the current time, and press the DIGITAL/ANALOG/BAND
button on the unit within 4 seconds.
Repeat the same procedure to restore the 12-hour standard.
In the 12-hour standard, “AM 12:00” indicates midnight and “PM
12:00” indicates noon.
Display the current time, and press the DIGITAL/ANALOG/BAND
button on the unit within 4 seconds.
Repeat the same procedure to restore the 12-hour standard.
In the 12-hour standard, “AM 12:00” indicates midnight and “PM
12:00” indicates noon.
If the clock display flashes while the power is off
This is caused by a power interruption. The current time needs
to be reset.
If power is interrupted for more than approximately 24 hours, all
settings stored in memory after purchase need to be reset.
This is caused by a power interruption. The current time needs
to be reset.
If power is interrupted for more than approximately 24 hours, all
settings stored in memory after purchase need to be reset.
The receiver can be automatically turned off at a specified time.
Press the SLEEP button while pressing the SHIFT button
on the remote control.
on the remote control.
The unit will be turned off after about 60 minutes.
To specify the time until the power is turned off
Within 4 seconds after the above, press the TUNING DOWN or
UP button repeatedly while pressing the SHIFT button.
You can change the time between 5 and 240 minutes in 5-minute
steps.
Within 4 seconds after the above, press the TUNING DOWN or
UP button repeatedly while pressing the SHIFT button.
You can change the time between 5 and 240 minutes in 5-minute
steps.
To check the time remaining until the power is turned off
Press the SLEEP button once while pressing the SHIFT button.
The remaining time is displayed for four seconds.
Press the SLEEP button once while pressing the SHIFT button.
The remaining time is displayed for four seconds.
To cancel the sleep timer
Press the SLEEP button twice while pressing the SHIFT button
so that “SLEEPoFF” appears on the display.
Press the SLEEP button twice while pressing the SHIFT button
so that “SLEEPoFF” appears on the display.
Specified time