Bosch nes730uc User Guide
NES Cooktop Use and Care Manual
Cooktop Operating Instructions
The Elements / Setting the Controls
PAGE 5
Radiant Elements
Bosch UltraSpeed
TM
radiant elements use a wire
ribbon located under the ceramic glass surface to
provide the heat for cooking. These radiant elements
will cycle on and off by design (see Temperature
Limiters, below.) There are 9 heat setting positions
from 9 (high) to 1 (low) and a special setting for keep
warm.
provide the heat for cooking. These radiant elements
will cycle on and off by design (see Temperature
Limiters, below.) There are 9 heat setting positions
from 9 (high) to 1 (low) and a special setting for keep
warm.
Dual Element
The dual element consists of two radiant ribbon
elements within the same heating area. Either the small
inner element or both the inner and outer elements
may be selected for use, depending on the size of
cookware. (See page 7.)
elements within the same heating area. Either the small
inner element or both the inner and outer elements
may be selected for use, depending on the size of
cookware. (See page 7.)
Temperature Limiters
Each UltraSpeed heating element has its own sensor
to protect the glass cooking surface from extreme
high temperatures. The limiters will operate
automatically by cycling the element on and off
regardless of the cook setting.
to protect the glass cooking surface from extreme
high temperatures. The limiters will operate
automatically by cycling the element on and off
regardless of the cook setting.
Although cycling is normal, any one of the following
conditions can activate the limiter and cause it to
cycle on and off more than usual:
•
conditions can activate the limiter and cause it to
cycle on and off more than usual:
•
The base of the pan is not making full contact
with the heating surface (due to a warped or
uneven base).
with the heating surface (due to a warped or
uneven base).
•
The pan is too small for the size of the element.
•
The pan has boiled dry.
•
The material or shape of the pan is slow to
transfer the heat.
transfer the heat.
Setting the Controls (dual element)
1. Place pan on element.
2. Touch element pad for desired element. Display
will show a 0.
will show a 0.
3. Touch POT SIZING pad. Control defaults to large
size (inner and outer) element. Touch the POT
SIZING element pad again for smaller element.
Touching the POT SIZING pad repeatedly alternates
the element size. The dual element light comes on
above element pad when using large element.
size (inner and outer) element. Touch the POT
SIZING element pad again for smaller element.
Touching the POT SIZING pad repeatedly alternates
the element size. The dual element light comes on
above element pad when using large element.
4. Turn the mTwisT dial to the desired setting.
To the right (clockwise) starts with heat setting
1 (low).
To the left (counterclockwise) starts with heat
setting 9 (high).
Turn the dial until the desired heat setting is
displayed.
1 (low).
To the left (counterclockwise) starts with heat
setting 9 (high).
Turn the dial until the desired heat setting is
displayed.
Setting the Controls (single element)
1. Follow steps 1, 2 and 4 above.
Changing Heat Setting While Cooking
1. Touch element pad for element desired. Display
will show 0.
will show 0.
2. Turn dial. The first turn of the mTwisT dial will
display the current cook setting.
display the current cook setting.
3. Turn dial left or right to new cook setting. The new
cook setting is displayed.
cook setting is displayed.
Change Pot Size when Cooking (for dual only)
See Pot Sizing (Page 6 ).
To Turn Off One Surface Element
1. Touch element pad for desired element.
1. Touch element pad for desired element.
2. Display shows 0. After 5 seconds the element
shuts off.
shuts off.
Or
touch element pad twice.
Or
touch element pad once. After five seconds,
the element turns off.
To Turn Off All Elements at the Same Time
1. Touch POWER OFF pad.
1. Touch POWER OFF pad.
Or
Remove mTwisT dial from cooktop. Once
removed, the cooktop controls are locked. Replace
mTwisT dial then touch and hold PANEL LOCK pad
for three seconds to unlock control.
mTwisT dial then touch and hold PANEL LOCK pad
for three seconds to unlock control.