Panasonic AJ-HPX3000 User Guide
135
Connection with external device : Connection with external devices using the USB 2.0 port
Co
nne
nne
cti
on wi
on wi
th
e
x
ter
nal
de
vi
nal
de
vi
ce
By connecting AJ-HPX3000 with an external PC using USB 2.0, the P2 card connected to AJ-HPX3000 can be used as a
mass storage device.
mass storage device.
1
Connect the USB cable to the USB 2.0 port.
Notes
z The USB 2.0 cable is not included with the camera-
recorder. Please use a commercially available USB
2.0 cable (shield with a ferrite core).
2.0 cable (shield with a ferrite core).
z It is recommended that the USB cable which is
within length 3 meters is used.
2
Navigate the menu to open the SYSTEM MODE
screen on the SYSTEM SETTING page. Then, set the
PC MODE SELECT menu option to USB DEV.and the
PC MODE option to ON.
screen on the SYSTEM SETTING page. Then, set the
PC MODE SELECT menu option to USB DEV.and the
PC MODE option to ON.
Note
The function of the menu option USB may be
assigned to a desired user button by using any one of
the menu options USER MAIN SW, USER1 SW or
USER2 SW.
These options can be found in the USER SW screen,
which is accessible from the CAM OPERATION page.
assigned to a desired user button by using any one of
the menu options USER MAIN SW, USER1 SW or
USER2 SW.
These options can be found in the USER SW screen,
which is accessible from the CAM OPERATION page.
Notes
z A USB driver must be installed on the PC.
z AJ-HPX3000 is only applicable to USB 2.0. Use a
z AJ-HPX3000 is only applicable to USB 2.0. Use a
personal computer that supports USB 2.0.
z Only one unit at a time must be connected to the
PC via USB.
z The P2 card must not be removed when it is
connected via USB.
z While a USB connection is established, the P2
card’s access LED should not be lit except when
access is being carried out.
access is being carried out.
z When a USB device is active, recording, playback,
or navigation through clip thumbnails is disabled.
During a USB connection, the USB LED on the side
panel stays illuminated. Also, “USB DEVICE” is
displayed in the system information/warning area in
the viewfinder.
When the connection is not correctly established,
both of these indications blink.
displayed in the system information/warning area in
the viewfinder.
When the connection is not correctly established,
both of these indications blink.
3
There are two ways to terminate the USB mode, as
follows:
z Turn the POWER switch of AJ-HPX3000 OFF.
z Set the PC MODE item to “OFF” from the menu
follows:
z Turn the POWER switch of AJ-HPX3000 OFF.
z Set the PC MODE item to “OFF” from the menu
operations.
Connection with external devices using the USB 2.0 port
Connection with a PC in the USB DEVICE mode
Procedures for establishing a connection with a
PC
PC
USB 2.0 port
(DEVICE)
(DEVICE)
# < SYSTEM MODE >
SYSTEM MODE :1080i-59.94i
REC SIGNAL :CAM
CAMERA MODE :60i
VF TYPE :HD
PC MODE SELECT :USB DEV.
REC SIGNAL :CAM
CAMERA MODE :60i
VF TYPE :HD
PC MODE SELECT :USB DEV.
# PC MODE :ON
When you establish the USB connection for the first time,
install the accessory P2 software for AJ-HPX3000 on the
PC. Refer to the Installation Manual for the details.
install the accessory P2 software for AJ-HPX3000 on the
PC. Refer to the Installation Manual for the details.
USB LED
8 6 % ' ( 9 , & (
)
$ ) ) =
w
w
E%
AJ-HPX3000G(VQT1D27)E.book 135 ページ ２００７年９月３日 月曜日 午後２時３４分