Panasonic AG-HPX500 User Guide
129
Setup menu list
C
h
ap
te
r 7 M
en
u O
p
p
er
at
io
n
s
OTHER FUNCTIONS screen
Item
Description of settings (Items in bold are factory settings.)
USER FILE
/
Saves users files on, loads users files from the storage area of the camera (EEPROM), and initializes
the storage area.
●
the storage area.
●
----:
Off (no operation)
●
LOAD: Loads the settings in a user file previously stored on the storage area.
●
SAVE: Saves the user file updated settings on the storage area.
●
INITIAL: Returns the user settings in the user file to their factory defaults.
• After a LOAD or INITIAL operation, turn the POWER switch off and then back on again to make the
new settings available.
• An INITIAL operation does not change the setting of the menu option TIME ZONE.
1394CONTROL
Sets the control method for backup recording using a backup unit connected to the 1394 terminal.
●
●
OFF: The backup unit is not controlled.
●
EXT: The backup unit can be controlled by the START/STOP button. The images shot by the camera
recorder are recorded by the backup unit. Note that the camera recorder does not record them.
●
BOTH: The images shot by the camera recorder are recorded by both the camera recorder and
backup unit.
●
CHAIN: When the camera recorder’s media approaches its end during shooting, the backup unit in
the recording standby mode automatically starts recording images.
When set to BOTH, direct shooting (function that automatically engages the CAMERA mode and starts
shooting when pressing the START/STOP button in the MCR mode) starts camera recording but does
not set a backup device to recording mode.
shooting when pressing the START/STOP button in the MCR mode) starts camera recording but does
not set a backup device to recording mode.
1394CMD SEL
Sets how the REC START/STOP button works for the backup unit.
●
●
REC_P: This switches between recording and pause.
●
STOP: This switches between recording and stop.
If the backup unit does not have a rec pause function, select STOP.
PC MODE
/
Selects the terminal for data transfer. (You cannot select USB and 1394 at the same time.)
●
●
USB DEVICE: Mode for sending files using the USB connector.
●
1394 DEVICE: Mode for sending files using the 1394 connector.
●
1394 HOST: Mode for copying files from the P2 card onto an external hard disk drive using the 1394
connector.
ACCESS LED
/
Enables or disables the access LED. The L-SIDE is the P2 card slot side.
(ON: LEDs turn on and blink normally. OFF: LEDs always stay off.)
●
(ON: LEDs turn on and blink normally. OFF: LEDs always stay off.)
●
OFF L-SIDE: OFF R-SIDE: OFF
●
SLOT SIDE L-SIDE: ON R-SIDE: OFF
●
LCD SIDE L-SIDE: OFF R-SIDE: ON
●
BOTH L-SIDE: ON R-SIDE: ON
ALARM
Turns the alarm function on and off.
●
●
ON, OFF
SAVE LED
/
Sets the SAVE lamp operation.
●
●
SAVE: Lights when the SAVE/STBY switch is set to SAVE.
●
P2CARD: Blinks when a warning message appears to indicate that there is little space left on a P2
card.
CLOCK SET
/
Sets the camera-recorder’s calendar.
●
●
----:
Does not set
●
YES: Sets
TIME ZONE
/
Adds to or deducts from GMT the time value of –12:00 to +13:00 in 30-minute steps. (As an exception,
you can set +12:45.)
●
you can set +12:45.)
●
0:00
LANGUAGE
/
Sets the Menu language.
●
●
ENGLISH
●
JAPANESE
●
CHINESE
GL SELECT
Determines which signal to lock on to.
●
●
SDI, COMPOSITE
GL PHASE
Determines whether to perform a 90H shift (ON) or not (OFF).
●
●
ON,
OFF
H PHASE
Adjusts the phase.
●
●
–512 ~
0 ~ +511
SYSTEM FREQ
/
Switches the system frequency.
●
●
59.94 Hz, 50 Hz (AG-HPX500P)
●
59.94 Hz,
50 Hz (AG-HPX500E)