Panasonic PV-GS400 User Guide
Before Use
16
ª Using the Remote Controller
1
1
Direct the Remote Controller at the Remote
Control Sensor
Control Sensor
of the Camcorder and
press an appropriate button.
≥Distance from the Camcorder: Within
approximately 15 feet (5 meters)
≥Angle: Within approximately 10o in the
upward, and 15
o in the downward and
horizontal directions from the central axis
≥The above operating ranges are for indoor use.
Outdoors or under strong light, the Camcorder
may not operate properly even within the above
ranges.
may not operate properly even within the above
ranges.
≥Within a 3 feet (1 meter) range, you can also
use the Remote Controller on the LCD Monitor
side of the Camcorder.
side of the Camcorder.
Selecting Remote Controller Modes
When 2 Camcorders are used simultaneously,
they can be operated individually by selecting
different Remote Controller Modes.
≥If the Remote Controller Mode of the Camcorder
When 2 Camcorders are used simultaneously,
they can be operated individually by selecting
different Remote Controller Modes.
≥If the Remote Controller Mode of the Camcorder
and that of the Remote Controller do not match,
[REMOTE] Indication is displayed.
[REMOTE] Indication is displayed.
Setup on the Camcorder:
Set [REMOTE] on the [INITIAL] Sub-Menu to the
desired Remote Controller Mode. (
Set [REMOTE] on the [INITIAL] Sub-Menu to the
desired Remote Controller Mode. (
,
Setup on the Remote Controller:
[VCR1]: Press the [
D] Button and [∫] Button
simultaneously.
1
[VCR2]: Press the [
E] Button and [∫] Button
simultaneously.
2
≥When the battery in the Remote Controller is
replaced, the mode is automatically reset to
[VCR1] Mode.
[VCR1] Mode.
10˚
15˚
15˚
15˚
INDEX
INDEX
SELECT
STOP
K
L
∫
STILL ADV
W
PAUSE STILL ADV
6
1
5
;
E
D
P.B. ZOOM
2
1
Power Supply
ª Using the AC Adaptor
1
Connect the DC Cable to the Camcorder.
2
Connect the DC Cable to the AC Adaptor.
3
Connect the AC Cable to the AC Adaptor
and the AC Jack.
≥The AC Cable’s outlet plug does not fit
and the AC Jack.
≥The AC Cable’s outlet plug does not fit
entirely into the AC Adaptor jack. A gap will
remain as shown
remain as shown
1.
≥Before connecting or disconnecting the
power supply, set the [OFF/ON] Switch on
the Camcorder to [OFF] and make sure that
[POWER] Lamp is not lit.
the Camcorder to [OFF] and make sure that
[POWER] Lamp is not lit.
ª Using the Battery
Before use, fully charge the Battery.
≥We recommend using a Panasonic Battery.
≥We cannot guarantee the quality of this
≥We recommend using a Panasonic Battery.
≥We cannot guarantee the quality of this
Camcorder when batteries from other
companies are used.
companies are used.
1
Attach the Battery to the AC Adaptor and
charge it.
charge it.
≥Since the Battery will not be charged when
the DC Cable is connected to the AC
Adaptor, disconnect it from the AC Adaptor.
Adaptor, disconnect it from the AC Adaptor.
≥The [CHARGE] Lamp lights up, and charging
starts.
≥When the [CHARGE] Lamp goes off,
charging is completed.
≥When the battery is completely discharged,
the [CHARGE] lamp blinks at first, but the
battery is charged normally. When the
temperature of the battery is too high or low,
the [CHARGE] lamp blinks and the charging
time becomes longer than usual.
battery is charged normally. When the
temperature of the battery is too high or low,
the [CHARGE] lamp blinks and the charging
time becomes longer than usual.
1
PV-GS400Eng.book 16 ページ 2004年6月4日 金曜日 午後3時17分