Panasonic CT-32HC14 User Guide
R
EMOTE
C
ONTROL
O
PERATION
11 z
ENGLISH
Programming The Remote Control
The Universal Remote Control can be programmed to
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, CABLE or
DBS. Follow the procedures for programming your Remote
Control with or without a code for the component.
operate many manufacturers’ components, using the
component function buttons for VCR, DVD, CABLE or
DBS. Follow the procedures for programming your Remote
Control with or without a code for the component.
Note:
Determine the manufacturer of the component and look
in the table for the code (found on page 12).
in the table for the code (found on page 12).
Procedure
1. Confirm that the external component is plugged in and
operating.
2. Turn the component off.
3. Press
and
together,
for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press appropriate component button on the Remote
Control VCR, DVD, CABLE or DBS. The component
button will illuminate steadily and all others will go out.
button will illuminate steadily and all others will go out.
5. Enter the 3-digit component code using the Remote
Control numeric keypad (0 ~ 9 buttons). The component
button will blink twice.
button will blink twice.
6. Press the Remote Control
to test the
component. If the procedure was successful, the
component will turn on and the component key will blink
twice and then go out.
component will turn on and the component key will blink
twice and then go out.
Note:
If the component does not operate with the Remote
Control, repeat steps 3 through 6 using another code
(some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Control, repeat steps 3 through 6 using another code
(some brands have multiple codes). If an incorrect code
is entered, or if the procedure takes longer than 30
seconds, the programming will fail.
Programming Without A Code
This procedure searches all codes and is called the
“sequence method.”
“sequence method.”
1. Confirm that the external component is plugged in and
on.
2. Turn the component off.
3. Press
and
together,
for at least 5
seconds. After 5 seconds, the illuminated mode
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
(component) buttons will begin to flash. Release the
ACTION and POWER buttons.
4. Press the appropriate component button on the Remote
Control. The component button will illuminate steadily
and all others will go out.
and all others will go out.
5. Press the
button to set the remote control into
the step and set mode.
6. Point the remote control towards the component.
7. Press VOL
(the mode key will blink three times), then
press the Remote Control
button to test the
component. Continue this process until the proper code
is found. If the procedure was successful, the component
will turn on.
is found. If the procedure was successful, the component
will turn on.
Note:
Each time you press the VOL button, make sure that
the component key blinks twice before pressing the
POWER button.
the component key blinks twice before pressing the
POWER button.
8. Once the device responds, press
to store the
code. The mode (component) button will blink twice.
Note:
It may take many attempts before the correct code
is found. If you miss a code, press
is found. If you miss a code, press
VOL, then press
the
button to test the component.
Component Codes
The Universal Remote Control is capable of operating
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all features found in each model.
many component brands after entering a code. Some
components may not operate because the codes are not
available due to limited memory. The Universal Remote
Control does not control all features found in each model.
Device
Operates
Default
TV
TV (Panasonic Only)
Panasonic Code
VCR
VCR (Preset)
Panasonic Code
DBS/CBL
DBS STB & CBL STB (Preset)
Panasonic DBS Code
DVD
DVD (Preset)
Panasonic Code
ACTION
POWER
POWER
ACTION
POWER
POWER
Write the code numbers from tables in this space.
This will serve as a reference if you need to program
your Remote Control.
VCR
CABLE
DVD
DBS
POWER
ACTION
POWER