Panasonic pt-50lcx7 User Guide
25
Basic Operation
First Time Setup
For your convenience, First Time Setup menu will
be displayed on screen when the set is turned on
for the first time. If needed, follow the menus and
procedures displayed on-screen for setting up the
features.
be displayed on screen when the set is turned on
for the first time. If needed, follow the menus and
procedures displayed on-screen for setting up the
features.
Language
The language of the on-screen display is set to English
as the factory setting. You can select English, Spanish or
French as the on-screen display language.
as the factory setting. You can select English, Spanish or
French as the on-screen display language.
Procedure
1. Press
▲▼ to select “Language”.
2. Press OK to display the Language menu.
3. Press
◄► to select “English,” “Español” or
“Français”.
4. Press RETURN to go to previous screen.
Auto program
You can scan All (Analog and Digital) channels. If
needed, follow the menus and procedures displayed
on-screen for setting up the features. You can also make
the settings in Setup menu.
needed, follow the menus and procedures displayed
on-screen for setting up the features. You can also make
the settings in Setup menu.
Procedure
1. Press
▲▼ to select “Auto program”.
2. Press OK to display the Program channel
menu.
3. Press
▲▼ to select “ANT in”.
4. Press
◄► to select “Cable” or “Antenna”.
Language
Auto program
Picture
First time setup
Language
Auto program
Picture
First time setup
Language
English
Language
Language
English
Language
Language
Auto program
Picture
First time setup
Language
Auto program
Picture
First time setup
ANT in
Auto
Cable
Program channel
ANT in
Auto
Cable
Program channel
5. Press
▲▼ to select “Auto”.
6. Press OK to display the Auto program menu.
7. Press
▲▼ to select “All channels”, “Analog
only”, or “Digital only”.
8. Press OK to start scan.
Channels available for reception will be set automatically.
9. After Auto program is complete, the unit will
return to Manual program mode. To place
the channels that were located by auto scan
in memory, move the cursor to “Apply” and
press OK. (p. 27-28)
If OK is not pressed after selecting APPLY,
the channels will not be memorized.
the channels that were located by auto scan
in memory, move the cursor to “Apply” and
press OK. (p. 27-28)
If OK is not pressed after selecting APPLY,
the channels will not be memorized.
10. Press
▲▼ to select “Picture”.
11. Press OK to display the Picture menu. (p. 35)
Notes
After “Auto program” is completed the unit tunes to the first
channel found during “Auto program”.
If setup is incomplete, check connection of Antenna/Cable to
the RF IN Terminal, then try “Auto program” again. (p. 26-27)
“Auto program” must be done when you select the input
signal for the first time or whenever you change the antenna
configuration.
Depending on conditions, “Auto program” may take a while.
channel found during “Auto program”.
If setup is incomplete, check connection of Antenna/Cable to
the RF IN Terminal, then try “Auto program” again. (p. 26-27)
“Auto program” must be done when you select the input
signal for the first time or whenever you change the antenna
configuration.
Depending on conditions, “Auto program” may take a while.
•
•
•
•
•
ANT in
Auto
Cable
Program channel
ANT in
Auto
Cable
Program channel
All channels
Analog only
Digital only
Auto program
Auto program
Scanning digital channel
Progress
Progress
Quit
40%
All channels
Analog only
Digital only
Auto program
Auto program
Scanning digital channel
Progress
Progress
Quit
40%
Language
Auto program
Auto program
Picture
First time setup
Language
Auto program
Auto program
Picture
First time setup