Panasonic bb-hgw700 User Manual
Operating Instructions
72
Data Entry Field
No.
Select an entry no. between 1 and 64. Packet filtering is processed from the
smallest entry no. up. If an entry is already registered, it will be overwritten
by the new entry.
smallest entry no. up. If an entry is already registered, it will be overwritten
by the new entry.
Operation
Click Add to add a new filtering setting. To modify or delete a filtering setting
click Modify/Delete. The setup page will open and you can add, modify or
delete settings by entering the data and clicking the appropriate button.
click Modify/Delete. The setup page will open and you can add, modify or
delete settings by entering the data and clicking the appropriate button.
Entry
Enable or Disable this entry.
Type
Select Permit (if it conforms to the parameters it will be passed) or Prohibit
(if it conforms to the parameters it will be intercepted).
(if it conforms to the parameters it will be intercepted).
Direction
Select W
L (filtering when receiving from WAN) or L
W (filtering when
sending to WAN).
Source IPv6
Address/Mask
Length
Address/Mask
Length
Set the source IPv6 address of the packet to be filtered.
•
•
When specifying only 1 IPv6 address, set the prefix length to 128. For
example, when setting 2002:C0A8:1234:0123:4567:89ab:cdef:0123/
128, enter 2002:C0A8:1234:0123:4567:89ab:cdef:0123 into the IPv6
address field and 128 into the prefix length field.
example, when setting 2002:C0A8:1234:0123:4567:89ab:cdef:0123/
128, enter 2002:C0A8:1234:0123:4567:89ab:cdef:0123 into the IPv6
address field and 128 into the prefix length field.
•
When specifying an IPv6 address range, usually set the prefix to a value
less than 64. For example, when setting 2002:C0A8:1234::/48, enter
2002:C0A8:1234:: into the IPv6 address field and 48 into the prefix
length field.
less than 64. For example, when setting 2002:C0A8:1234::/48, enter
2002:C0A8:1234:: into the IPv6 address field and 48 into the prefix
length field.
•
If "
" is entered in the IPv6 address field, all packets are filtered.
Note
When specifying an IPv6 address range, even if this product's IPv6
address is included in the range, this product will not be filtered. When
you want to filter this product, it is necessary to enter "
When specifying an IPv6 address range, even if this product's IPv6
address is included in the range, this product will not be filtered. When
you want to filter this product, it is necessary to enter "
" or the code for
this product (local) in the IPv6 address data field.
Source Port
Set the source port of the packet to be filtered.
•
•
When using only 1 port, enter the port number.
•
When entering a range, enter "-" in between the numbers. For example,
when you want to use port numbers 2000 to 3000, enter "2000-3000".
The number on the left should be lower than the number on the right.
when you want to use port numbers 2000 to 3000, enter "2000-3000".
The number on the left should be lower than the number on the right.
•
If "
" is entered, all packets are filtered.
Destination IPv6
Address/Mask
Length
Address/Mask
Length
Set the destination IPv6 address of the packet to be filtered. Entry is the
same as for the source IPv6 address. When you want to specify this
product, enter "local".
same as for the source IPv6 address. When you want to specify this
product, enter "local".
Destination Port
Set the destination port number of the packet to be filtered. Entry is the
same as for the Source Port.
same as for the Source Port.
Note
The port numbers (53, 80[camera portal page], 1723, 8080[setup
page]), are used by this product. Set a different port number.
The port numbers (53, 80[camera portal page], 1723, 8080[setup
page]), are used by this product. Set a different port number.