KYOCERA FS-C5016N Installation Guide
Continued on
the Reverse Page
Packing Cover
Packing
Tape
Tape
Packing
Item
Magenta (M)
Cyan (C)
Yellow (Y)
Black (K)
Cyan (C)
Yellow (Y)
Black (K)
Lock Lever
Cap
USB Interface
Parallel
Interface
Network Interface
(Ethernet)
(Ethernet)
Power Cord
Connecter
Connecter
Toner Supply
Opening
Opening
FS-C5016N
Important!
Kyocera Mita assumes no liability for any damage caused by an improper
installation of the printer.
installation of the printer.
Installation Guide
Unpacking
Checking Parts and Components
Installing the Toner Containers and Waste Toner Box
Close the paper transfer
unit tightly.
unit tightly.
Unpack the printer and all its included components.
Remove the
packing cover and
all packing tapes.
packing cover and
all packing tapes.
Open the top cover and remove
the packing item.
the packing item.
In this example, it is assumed that you are
installing the black toner container.
installing the black toner container.
DO NOT forcefully push in on the center of the
toner container or touch the toner supply opening
with your hands or fingers during this procedure.
toner container or touch the toner supply opening
with your hands or fingers during this procedure.
Make sure that the side of the toner
container with the markings (caution
notes, etc.) are facing downward,
and shake the new toner container 5
or 6 times as shown in the figure in
order to distribute the toner evenly
inside the container.
container with the markings (caution
notes, etc.) are facing downward,
and shake the new toner container 5
or 6 times as shown in the figure in
order to distribute the toner evenly
inside the container.
Set the new toner container in
the printer with the markings
facing upward as shown in the
figure below.
the printer with the markings
facing upward as shown in the
figure below.
Note
Be sure you set the toner
container in the correct location
for that color.
container in the correct location
for that color.
Install the toner container by
pushing down on the container
until it clicks firmly into place.
pushing down on the container
until it clicks firmly into place.
To install the other color toner containers,
use the same procedure as above.
use the same procedure as above.
Close the top cover.
Open the left cover.
Open the cap of the waste
toner box.
toner box.
Install the waste toner box into the
printer as shown in the figure by
setting the bottom of the box into
the receptacle, and then pushing
down on the box until it snaps firmly
into place.
printer as shown in the figure by
setting the bottom of the box into
the receptacle, and then pushing
down on the box until it snaps firmly
into place.
Make sure that the waste toner
box is correctly inserted and
close the left cover.
box is correctly inserted and
close the left cover.
1 Printer
2 Documents and Software
2 Documents and Software
• Installation Guide
(This sheet)
• Quick Reference Guide
• CD-ROMs
(This sheet)
• Quick Reference Guide
• CD-ROMs
3 Magenta Toner Container
4 Cyan Toner Container
5 Yellow Toner Container
6 Black Toner Container
7 Waste Toner Boxes
(One is spare.)
8 Power Cord
4 Cyan Toner Container
5 Yellow Toner Container
6 Black Toner Container
7 Waste Toner Boxes
(One is spare.)
8 Power Cord
Connect the printer to your computer. (The connecting
cable is sold separately.)
cable is sold separately.)
Connect the provided power
cord to a power outlet.
cord to a power outlet.
Turn on ( | ) the printer’s power
switch (located on the rear side
of the printer).
switch (located on the rear side
of the printer).
8
1
2
5
6
4
3
7
Be sure to hold the
right and left sides
of the printer when
carrying it, as shown
in the illustration.
right and left sides
of the printer when
carrying it, as shown
in the illustration.
Rear
Apply light pressure to the toner
container and push the blue lock
lever on the toner container back
towards the locked symbol ( ) as
far as it will go.
container and push the blue lock
lever on the toner container back
towards the locked symbol ( ) as
far as it will go.
Making Connections
l Avoid installing the printer on unstable surfaces and surfaces that are not level.
Basic installation is now complete. Before using the printer, refer to “Setting the Color
Registration” on the reverse page and use the printer
Registration” on the reverse page and use the printer
’
s operation panel to perform the color
registration procedure.
U.S.A./Canada
European/Pacific
countries
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17