Silver King skr27 User Guide
1
TECHNICAL MANUAL
SILVER KING FRONT BREATHING REFRIGERATOR
MODELS SKR27, SKR27B, SKR27D, SKR27BD
Thank you for purchasing Silver King food service equipment. Our goal is to provide our customers with the most reliable
equipment in the industry today. Please read this manual and the accompanying warranty information before operating your new
Silver King unit. Be sure to complete and mail the warranty card within 10 days of purchase to validate your warranty.
INSPECT FOR DAMAGE AND UNCRATE
Upon delivery of your new Silver King unit, uncrate at once to inspect for possible freight damage following the instructions printed
on the exterior of the container. Report any damages to the carrier responsible for transportation and promptly present a claim for
any evidence of mishandling. Save all packaging materials if a claim is filed.
INSTALLATION
The stainless steel exterior of the cabinet has been protected by a plastic covering during manufacturing and shipping. This
covering can be readily stripped before installation. After removing this covering, wash the interior and exterior surfaces using a
warm, mild soapy water solution and a sponge or cloth, rinse with clean water and dry.
Legs/Casters
Models without a base come with Legs or Casters. To install them, tilt the unit and thread the Legs or Casters into the four Rivnuts
in the bottom of the cabinet. Make sure that they are installed tightly to prevent future thread wear.
Condenser Filter Screen
On models without a base, the Condenser Filter Screen, Screen Pull and Filter Guides are packaged inside the cabinet. The
instructions for installing these parts are included in this technical manual. On models with a base, the Condenser Filter Screen is
factory mounted behind the Base Grill. Remove the Base Grill and ensure that the Condenser Filter Screen is in place. Do not
operate the unit without the filter screen installed!
Shelves
Inside the unit you will find Shelves and a plastic bag containing Shelf Supports. The Shelf Supports with the “tang” go on the rear
Pilasters. This shelf system allows for easy adjustment to suit your needs.
Door Adjustment and Swing
Should the Door ever require straightening, loosen the Screws on the Hinges, square the Door with the cabinet and retighten the
Screws.
The mounting of the Door is easily reversible on single door units should space or convenience require that you do so. Simply
remove the Screws holding the Hinges, rotate the Door 180 degrees and relocate the Hinges on the side opposite their original
location.
Drawers
To remove the Drawers on drawer models for cleaning, simply open them fully, push the Stop Levers out of the way on the Cabinet
Drawer Tracks while pulling the Drawer out. To reinstall the Drawer, line up the drawer tracks on the cabinet and the Drawer and
push the Drawer into the cabinet. The Drawer Pan can be removed by lifting it out with the Drawer fully extended.
Location
When locating your new refrigerator, convenience and accessibility are important considerations, but the following installation
guidelines must be followed;
equipment in the industry today. Please read this manual and the accompanying warranty information before operating your new
Silver King unit. Be sure to complete and mail the warranty card within 10 days of purchase to validate your warranty.
INSPECT FOR DAMAGE AND UNCRATE
Upon delivery of your new Silver King unit, uncrate at once to inspect for possible freight damage following the instructions printed
on the exterior of the container. Report any damages to the carrier responsible for transportation and promptly present a claim for
any evidence of mishandling. Save all packaging materials if a claim is filed.
INSTALLATION
The stainless steel exterior of the cabinet has been protected by a plastic covering during manufacturing and shipping. This
covering can be readily stripped before installation. After removing this covering, wash the interior and exterior surfaces using a
warm, mild soapy water solution and a sponge or cloth, rinse with clean water and dry.
Legs/Casters
Models without a base come with Legs or Casters. To install them, tilt the unit and thread the Legs or Casters into the four Rivnuts
in the bottom of the cabinet. Make sure that they are installed tightly to prevent future thread wear.
Condenser Filter Screen
On models without a base, the Condenser Filter Screen, Screen Pull and Filter Guides are packaged inside the cabinet. The
instructions for installing these parts are included in this technical manual. On models with a base, the Condenser Filter Screen is
factory mounted behind the Base Grill. Remove the Base Grill and ensure that the Condenser Filter Screen is in place. Do not
operate the unit without the filter screen installed!
Shelves
Inside the unit you will find Shelves and a plastic bag containing Shelf Supports. The Shelf Supports with the “tang” go on the rear
Pilasters. This shelf system allows for easy adjustment to suit your needs.
Door Adjustment and Swing
Should the Door ever require straightening, loosen the Screws on the Hinges, square the Door with the cabinet and retighten the
Screws.
The mounting of the Door is easily reversible on single door units should space or convenience require that you do so. Simply
remove the Screws holding the Hinges, rotate the Door 180 degrees and relocate the Hinges on the side opposite their original
location.
Drawers
To remove the Drawers on drawer models for cleaning, simply open them fully, push the Stop Levers out of the way on the Cabinet
Drawer Tracks while pulling the Drawer out. To reinstall the Drawer, line up the drawer tracks on the cabinet and the Drawer and
push the Drawer into the cabinet. The Drawer Pan can be removed by lifting it out with the Drawer fully extended.
Location
When locating your new refrigerator, convenience and accessibility are important considerations, but the following installation
guidelines must be followed;
• Always avoid placing the refrigerator adjacent to an oven, heating element or hot air source that would affect the operation of the
unit.
• For proper ventilation the bottom front of the unit must not be obstructed. The unit must be on legs or casters to raise it off the
floor. The unit can be installed tight on the sides and back.
• The unit must be level or tilted backwards slightly.