Sony CDX-L510X Installation Guide
Sony Corporation © 2003 Printed in Korea
3-247-736-11
(1)
Cautions
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected wires
with electrical tape for safety.
• The use of optical instruments with this product
will increase eye hazard.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
• The numbers in the list are keyed to those in the
instructions.
• The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar 3
from the unit. For details, see “Removing the
protection collar and the bracket (4)” on the
reverse side of the sheet.
mounting the unit, use the release keys 5 to
remove the bracket 1 and the protection collar 3
from the unit. For details, see “Removing the
protection collar and the bracket (4)” on the
reverse side of the sheet.
• Keep the release keys 5 for future use as they
are also necessary if you remove the unit from
your car.
your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
your fingers.
Note
Before installing, make sure that the catches on both
sides of the bracket
sides of the bracket
1
are bent inwards 2 mm (
3
/
32
in). If
the catches are straight or bent outwards, the unit will
not be installed securely and may spring out.
not be installed securely and may spring out.
Installation/Connections
Installation/Connexions
FM/AM
Compact Disc
Player
Compact Disc
Player
Connection example (2)
Notes (2-B)
• Be sure to connect the ground cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
be deactivated.
Connection diagram (3)
1
To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.
the yellow and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is
no power antenna or antenna booster, or with
a manually-operated telescopic antenna.
a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
3
To AMP REMOTE IN of an optional power
amplifier
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
any other system may damage the unit.
4
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
and power supply leads.”
5
To the +12 V power terminal which is
energized at all times
energized at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
metal surface of the car first.
2
A
B
AUDIO OUT REAR
1
4
5
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Appareils utilisés dans les illustrations (non fournis)
Rear speaker
Haut-parleur arrière
Haut-parleur arrière
Front speaker
Haut-parleur avant
Haut-parleur avant
1
Power amplifier
Amplificateur de puissance
Amplificateur de puissance
Rotary commander RM-X4S
Satellite de commande RM-X4S
Satellite de commande RM-X4S
×
4
2
×
2
3
CDX-L510X
1
Catch