Sony dsx-s210x Manual
24
Searching a track by listening
to track passages — ZAPPIN™
to track passages — ZAPPIN™
While playing back short track passages in a
USB device in sequence, you can search for a
track you want to listen to.
ZAPPIN mode is suitable for searching for a
track in shuffle or shuffle repeat mode.
USB device in sequence, you can search for a
track you want to listen to.
ZAPPIN mode is suitable for searching for a
track in shuffle or shuffle repeat mode.
1
Press (ZAP/SHUF) during playback.
After “ZAPPIN” appears in the display,
playback starts from a passage of the next
track.
The passage is played for the set time, then a
click sounds and the next passage starts.
After “ZAPPIN” appears in the display,
playback starts from a passage of the next
track.
The passage is played for the set time, then a
click sounds and the next passage starts.
2
Press the multi-way encoder or
(ZAP/SHUF) when a track you want to
listen is played back.
The track that you select returns to normal
play mode from the beginning.
To search a track by ZAPPIN mode again,
repeat steps 1 and 2.
(ZAP/SHUF) when a track you want to
listen is played back.
The track that you select returns to normal
play mode from the beginning.
To search a track by ZAPPIN mode again,
repeat steps 1 and 2.
In the case of “SensMe™
channels” playback
channels” playback
If the track being searched is transferred by
“Content Transfer,” the most melodic or
rhythmical sections* of tracks are played. For
details on the SensMe™ function, see page 15.
“Content Transfer,” the most melodic or
rhythmical sections* of tracks are played. For
details on the SensMe™ function, see page 15.
* May not be detected correctly.
Tips
• You can select the playback time from about 6
• You can select the playback time from about 6
seconds/15 seconds/30 seconds (page 28). You
cannot select the passage of the track to playback.
cannot select the passage of the track to playback.
• Push the multi-way encoder left/right in ZAPPIN
mode to skip a track.
• Push the multi-way encoder up/down in ZAPPIN
mode to skip album.
Sound Settings and Setup Menu
Changing the sound settings
Adjusting the sound
characteristics
characteristics
1
During reception/playback, press the
multi-way encoder.
multi-way encoder.
2
Rotate the multi-way encoder until the
desired menu item appears, then
press it.
desired menu item appears, then
press it.
3
Use the multi-way encoder to select
the setting, then press it.
the setting, then press it.
4
Press
(BACK).
The setting is complete and the display
returns to normal reception/play mode.
returns to normal reception/play mode.
The following items can be set:
The operation of the multi-way encoder will
differ depending on the items.
The operation of the multi-way encoder will
differ depending on the items.
: Push the multi-way encoder up/down
: Push the multi-way encoder left/right
: Rotate the multi-way encoder
: Push the multi-way encoder left/right
: Rotate the multi-way encoder
The part of each track to
playback in ZAPPIN mode.
playback in ZAPPIN mode.
Track
(ZAP/SHUF)
pressed.
pressed.
EQ7 Preset (page 25)
EQ7 Parametric Tune (page 25)
Listening Position Front/Rear (page 25)
Listening Position Subwoofer (page 26)
Listening Position Custom Tune (page 26)
Fader & Balance
Front/Rear/Center (
)
Adjusts the relative level.
Right/Left/Center (
Right/Left/Center (
)
Adjusts the sound balance.
Subwoofer Tune & LPF
Phase (
)
Selects the phase: “Normal,” “Reverse.”
FREQ (
FREQ (
)
Selects the subwoofer cut-off frequency:
“50Hz,” “60Hz,” “80Hz,” “100Hz,” “120Hz.”
Slope (
“50Hz,” “60Hz,” “80Hz,” “100Hz,” “120Hz.”
Slope (
)
Selects the LPF slope: ”1,” ”2,” ”3.”
Subwoofer Level (
)
Adjusts the subwoofer volume: “+10 dB” –
“0 dB” – “–10 dB.”
(“–
“0 dB” – “–10 dB.”
(“–
∞” is displayed at the lowest setting.)
HPF
FREQ (
)
Selects the cut-off frequency: “off,” “50Hz,”
“60Hz,” “80Hz,” “100Hz,” “120Hz.”
Slope (
“60Hz,” “80Hz,” “100Hz,” “120Hz.”
Slope (
)
Select the HPF slope: ”1,” ”2,” ”3.”
DM+ Advanced (page 26)
Rear Bass Enhancer (page 27)