Insignia ns-lcd19w-09 User Guide
9
Insignia NS-LCD19W-09 19” LCD TV
www.insignia-products.com
Using the remote control
To use the remote control:
•
•
Point the remote control directly at your TV,
within a 60° angle horizontally (30° to either
side), and within 30° vertically of the remote
control sensor on the front of your TV and
within 26.25 feet (8 m) of your TV.
within a 60° angle horizontally (30° to either
side), and within 30° vertically of the remote
control sensor on the front of your TV and
within 26.25 feet (8 m) of your TV.
Setting up your TV
Connecting an antenna, cable TV, or
satellite TV
satellite TV
Grounding
Make sure that you connect the grounding/earth
wire to prevent possible electric shock. If
grounding methods are not possible, have a
qualified electrician install a separate circuit
breaker. Do not ground the TV by connecting it
to telephone wires, lightening rods, or gas pipes.
wire to prevent possible electric shock. If
grounding methods are not possible, have a
qualified electrician install a separate circuit
breaker. Do not ground the TV by connecting it
to telephone wires, lightening rods, or gas pipes.
Connecting an antenna
Antenna cables come in two types: 75 ohm and
300 ohm.
300 ohm.
•
If your antenna cable has a 75 ohm
connector, connect the cable to the coaxial
jack on the back of your TV.
connector, connect the cable to the coaxial
jack on the back of your TV.
•
If your antenna cable has a 300 ohm
connector, connect the cable to a
300-75 ohm adapter (not included), connect
the adapter to a 75 ohm cable, then connect
the other end of the 75 ohm connector to the
coaxial jack on the back of your TV.
connector, connect the cable to a
300-75 ohm adapter (not included), connect
the adapter to a 75 ohm cable, then connect
the other end of the 75 ohm connector to the
coaxial jack on the back of your TV.
Connecting cable TV
Your TV has a 75 ohm jack for connecting cable
TV.
Some cable TV providers scramble the signals
for “premium” (pay) channels. To view these
channels, you need a converter/descrambler
box.
If you do not have a converter/descrambler box,
you can connect your cable TV directly to your
TV. If you have a converter/descrambler box, you
can connect your cable TV using an RF switch
(not supplied). For more information about
connecting a converter/descrambler box, contact
your cable TV provider.
TV.
Some cable TV providers scramble the signals
for “premium” (pay) channels. To view these
channels, you need a converter/descrambler
box.
If you do not have a converter/descrambler box,
you can connect your cable TV directly to your
TV. If you have a converter/descrambler box, you
can connect your cable TV using an RF switch
(not supplied). For more information about
connecting a converter/descrambler box, contact
your cable TV provider.
To connect an antenna or cable TV:
1 Connect the antenna cable from an antenna,
or cable TV to the ANT IN jack on the back of
your TV.
your TV.
2 Turn on your TV.
3 Press INPUT repeatedly to select TV.
Caution
Do not expose the remote control to liquids, direct
sunlight, or shock. Do not mix batteries of different
types.
sunlight, or shock. Do not mix batteries of different
types.
Notes
•
Objects between the remote control and the
remote control sensor may block the remote
control signal.
remote control sensor may block the remote
control signal.
•
The range of the remote control may be
diminished if direct sunlight or other strong light
is shining on the remote control sensor. In this
case, change the angle of the lighting, move
your TV, or operate the remote control closer to
the remote control sensor.
diminished if direct sunlight or other strong light
is shining on the remote control sensor. In this
case, change the angle of the lighting, move
your TV, or operate the remote control closer to
the remote control sensor.
75 ohm cable
300 ohm cable