ONKYO HT-S8400 User Manual
29
En
Note
• You can cancel Audyssey 2EQ Room Correction and Speaker
Setup at any point in this procedure simply by disconnecting the
setup microphone.
setup microphone.
• Do not connect or disconnect any speakers during
Audyssey 2EQ Room Correction and Speaker Setup.
• If the AV receiver is muted, it will be unmuted automatically
when Audyssey 2EQ Room Correction and Speaker Setup
starts.
starts.
• Changes to the room after Audyssey 2EQ Room Correction and
Speaker Setup requires you run Audyssey 2EQ Room
Correction and Speaker Setup again, as room EQ characteristics
may have changed.
Correction and Speaker Setup again, as room EQ characteristics
may have changed.
3
When you’ve finished making the settings, press
ENTER.
ENTER.
Perform the “Speaker Setup” according to your
speaker configuration:
speaker configuration:
– Powered Zone 2 (
)
– Surround Back/Front High (
)
When an optional unit is connected to the
UNIVERSAL PORT jack on the AV receiver, the
optional unit setting may appear on the speaker
setting menu.
UNIVERSAL PORT jack on the AV receiver, the
optional unit setting may appear on the speaker
setting menu.
4
Use
q/w to select “Audyssey Quick Start” or
“Audyssey 2EQ Full Calibration”.
5
Press
ENTER.
Audyssey 2EQ
®
Room Correction and Speaker Setup
starts.
Test tones are played through each speaker as
Audyssey 2EQ Room Correction and Speaker Setup
runs. This process takes a few minutes. Please
refrain from talking during measurements and do
not stand between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey 2EQ Room Correction and Speaker
Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 8.
Test tones are played through each speaker as
Audyssey 2EQ Room Correction and Speaker Setup
runs. This process takes a few minutes. Please
refrain from talking during measurements and do
not stand between speakers and the microphone.
Do not disconnect the speaker setup microphone
during Audyssey 2EQ Room Correction and Speaker
Setup, unless you want to cancel the setup.
If you select “Audyssey Quick Start”, you will go to
step 8.
6
Place the setup microphone at the next position,
and then press
and then press
ENTER.
Audyssey 2EQ performs more measurements. This
takes a few minutes.
takes a few minutes.
7
When prompted, repeat step 6.
8
Use
q/w to select an option, and then press
ENTER.
The options are:
`
Save:
Save the calculated settings and exit
Audyssey 2EQ
Audyssey 2EQ
Room Correction and Speaker
Setup
.
`
Cancel:
Cancel Audyssey 2EQ
Room Correction and
Speaker Setup
.
Tip
• You can view the calculated settings for the speaker
configuration, speaker distances, and speaker levels by
using
e/r.
2EQ: Auto Setup
AUDYSSEY
Powered Zone 2
No
Surround Back/Front High
Surround Back
Subwoofer :
Yes
Front :
100Hz
Center :
40Hz
Surround :
100Hz
Front High
:
None
Surround Back
:
120Hz
Surround Back Ch
:
2ch
Save
Cancel
Cancel
2EQ: Auto Setup
AUDYSSEY
-- Review Speaker Configuration --
9
Use
q/w to select a target, and use e/r to change
the setting.
After the results of Audyssey 2EQ have been saved,
the menu will display the “Audyssey” (
After the results of Audyssey 2EQ have been saved,
the menu will display the “Audyssey” (
(
Note
• When “Audyssey Quick Start” has been used for
measurement, “Audyssey” cannot be selected.
• These settings are applied to all input selectors.
10
Press
ENTER.
11
Disconnect the speaker setup microphone.