Pelican SabreLite 2000 Flashlight - Xenon Bulb - 3.30 W - C - ABSBody, 2000-010-245 Leaflet

Product codes

2000-010-245

PELICAN

SabreLite

2000

OPERATING INSTRUCTIONS

CATALOG #2000

23215 Early Ave. • Torrance, CA 90505

(310) 326-4700 • FAX (310) 326-3311

www.pelican.com

All trademarks and logos displayed herein are registered and

unregistered trademarks of Pelican Products, Inc. and others.

Energizer and Energizer a registered trademarks

of Eveready Battery Company, Inc.

SabreLite

2000

OPERATING INSTRUCTIONS CATALOG #2000

BATTERY INSTALLATION

1. Remove lens housing by turning counter-clockwise.

2. Remove the lamp module.

3. Remove the battery tray.

4. Remove used batteries and replace with fresh batteries in the tray as

shown by the polarity icons molded into the base of the tray battery.

5. Insert the battery tray into the flashlight with the two metal tabs fac-

ing outwards.

6. Replace the lamp module.

7. Replace lens housing squarely on threads and turn

clockwise while pressing on the lens housing slightly.

ON/OFF

Turn the lens housing clockwise until light activates.

To turn light off, back lens housing off counter-clockwise until light goes

off. Continue to back off for approximately 1 full turn to eliminate possibil-

ity of light activating accidentally in storage. DO NOT OVERTIGHTEN.

LAMP REPLACEMENT

To replace the lamp module follow steps in the

battery installation section as listed below:

To remove lamp module follow steps #1 and #2.

To replace lamp module follow steps #6 and #7.

WARNING –

Explosion Hazard - Batteries must only be changed in

non-hazardous locations

WARNING –

Explosion Hazard - Substitution of components may

impair suitability for use in hazardous locations

CAUTION:

If light is not to be used for some time, remove batteries to prevent

possible leakage and corrosion.

PRODUCT SPECIFICATIONS

Lamp Type:

Xenon

Battery Type:

E93 1.5V Alkaline C-cell (3)

Battery Brand:

Eveready

Energizer

REPLACEMENT PARTS

2001

O-ring

2004 Lamp Module

CAUTION: Read This Notice Before Use.

Hydrogen Gas Absorber Pellets

Located inside the flashlight are catalyst pellets which are present

to absorb hydrogen gas that could possibly be emitted by defective,

leaking, reversed polarity or heavily discharged batteries. If the pellets

become wet, let them air dry. Pelican Products assumes no liability

for any brand batteries which are defective or cause injury to anyone

when used in any Pelican flashlight.

Battery Replacement

Battery replacement may only be performed in a non-hazardous area.

Do not mix battery brands or use Nicad or Zinc Carbon Batteries.

Do not mix old and new batteries. Replace all batteries at the

same time.

Lamp Replacement

Lamp replacement may only be performed in a non-hazardous area.

DO NOT MODIFY THIS PRODUCT!

SabreLite

2000

INSTRUCCIONES DE FUNCIONAMIENTO #CAT. 2000

INSTALACIÓN DE LAS PILAS

1. Retire el bastidor de la lente girándolo en sentido contrario

a las agujas del reloj.

2. Retire el módulo de la bombilla.

3. Retire la bandeja de pilas.

4. Retire las pilas usadas y coloque las pilas nuevas en la bandeja

teniendo en cuenta la polaridad como se muestra en la ilustración

impresa en la base de la bandeja.

5. Inserte la bandeja de pilas en la linterna con las dos piezas metálicas

apuntando hacia afuera.

6. Vuelva a colocar el módulo de la bombilla.

7. Vuelva a colocar el bastidor de la lente sobre la rosca y gire en el

sentido de las agujas del reloj al mismo tiempo que ejerce un poco

de presión sobre el mismo.

ENCENDIDO / APAGADO

La luz se enciende girando el bastidor de la lente en el sentido de las

agujas del reloj. Para apagarla, gire en sentido opuesto hasta que se

apague la luz. Siga girando aproximadamente una vuelta completa para

eliminar la posibilidad de que la luz se encienda por error al estar guar-

dada. NO APRIETE DEMASIADO.

REEMPLAZO DE LA BOMBILLA

Para cambiar el módulo de la bombilla, siga los pasos especificados para

la instalación de las pilas que aparecen a continuación:

Para retirar el módulo de la bombilla, siga los pasos No. 1 y 2.

Para cambiar el módulo de la bombilla, siga los pasos No. 6 y 7.

23215 Early Ave. • Torrance, CA 90505 USA

Tel (310) 326-4700 • FAX (310) 326-3311

www.pelican.com

PELICAN

CANADA

10221-184 St. • Edmonton, Alberta T5S 2J4

Tel (780) 481-6076 • FAX (780) 481-9586

PELI

PRODUCTS, S.L.U.

c/ Casp, 33-B Pral. • 08010 • Barcelona, Spain

Tel (+34) 93.467.4999 • FAX (+34) 93.487.7393 • www.peli.com

Submersible

WARRANTY RETURN POLICY

Send all items for repair or replacement directly to Pelican Products

Customer Service Department (postage paid). Please call for a return

authorization number. Per our guarantee, Pelican Products will replace

or repair any broken or defective products. Upon receipt of goods,

Pelican Products will notify you of any handling and return postage

charges. If your local retailer does not stock the above accessory

parts, you may order them directly from Pelican Products. Send check

or money order in U.S. dollars, or order by phone using MasterCard

or VISA (ask for Customer Service). SORRY, NO C.O.D.’s. Subject

to sales tax. Allow 2-3 weeks delivery time. Pelican Products pays

postage and handling charges.

PELICAN LEGENDARY LIFETIME

GUARANTEE OF EXCELLENCE

Pelican Products, Inc. guarantees its products for a lifetime

against breakage or defects in workmanship. This guarantee

does not cover the lamp or batteries (rechargeable or alkaline).

Any liability, either expressed or implied, is limited to replacement

of the product. This guarantee is void if the Pelican product has

been abused beyond normal and sensible use. This guarantee

does not cover shark bite, bear attack or damage caused by

children under five.

Lifetime Guarantee does not cover Roto Molded or AALG prod-

ucts. Refer to www.pelican.com/warranty for full details.