Hotpoint hsh25gfb User Guide

Page of 64
About the water filter cartridge. 
(On some models.)
www.Hotpoint.com
Water Filter Cartridge
The water filter cartridge is located in the back upper right
corner of  the refrigerator compartment.
When to Replace the Filter on Models With a 
Replacement Indicator Light
There is a replacement indicator light for the water filter
cartridge on the dispenser. This light will turn orange to tell you
that you need to replace the filter soon.
The filter cartridge should be replaced when the replacement
indicator light turns red or if  the flow of  water to the dispenser or
icemaker decreases.
When to Replace the Filter on Models Without a
Replacement Indicator Light
The filter cartridge should be replaced every six months
or earlier if  the flow of  water to the water dispenser or icemaker
decreases.
Removing the Filter Cartridge
If  you are replacing the cartridge, first remove the old one by
slowly turning it to the left. Do not pull down on the cartridge. A
small amount of  water may drip down.
Installing the Filter Cartridge
If you are replacing a
SmartWater
cartridge
with an adapter, it must
be removed before
installing the cartridge.
To remove the adapter,
turn it to the left about
1/4 turn.
If  you are replacing a
Water by Culligan
cartridge,
leave the adapter in place.
This adapter will stay in the refrigerator when you replace
future cartridges.
On models without a replacement indicator light, 
apply the month and year sticker to the new cartridge to
remind you to replace the filter in six months.
Fill the replacement cartridge with water from the tap to
allow for better flow from the dispenser immediately after
installation.
Line up the arrow on the cartridge and the cartridge holder.
Place the top of  the new cartridge up inside the holder. Do
not
push it up into the holder.
Slowly turn it to the right until
the filter cartridge stops. DO
NOT OVERTIGHTEN.
As you turn
the cartridge, it will
automatically raise itself  into
position. The cartridge will
move about 1/2 turn.
Run water from the dispenser
for 1-1/2 gallons (about three
minutes) to clear the system and prevent sputtering.
Press and hold the RESET WATER FILTER pad (on 
some models) on the dispenser for three seconds.
Filter Bypass Plug
You must use the filter bypass plug when a replacement filter
cartridge is not available. The dispenser and the icemaker will not
operate without the filter or filter bypass plug.
To use the filter bypass plug on Water by Culliganmodels, you must first remove
the filter adapter from the cartridge holder by turning it to the left.
For the maximum benefit of  your filtration system, GE
recommends the use of  GE branded SmartWater filters only.
Using GE branded filters in GE and Hotpoint refrigerators
provides optimal performance and reliability.  GE branded
SmartWater filters are always the right choice because they are
patented and designed specifically for GE products.  GE
SmartWater filters meet rigorous industry NSF standards for
safety and quality that are important for products that are
filtering your water.  GE has not qualified non-GE branded filters
for use in GE and Hotpoint refrigerators and there is no
assurance that non-GE branded filters meet GE’s standards for
quality, performance and reliability.
If  you have questions—visit our Website 
at www.hotpoint.com, 
or call 1.800.GE.CARES (1.800.432.2737).
Replacement filters:
To order additional filter cartridges in the United States, 
visit our Website at www.hotpoint.com, or call GE Parts and
Accessories, 800.626.2002.
MWF
Suggested Retail $38.95–47.95
Customers in Canada should consult the yellow pages for the
nearest Mabe Service Center.
Customers outside of  the United States or Canada should
contact the local distributor.
Cartridge
Holder
Filter
Bypass
Plug
Filter 
Bypass
Plug
SmartWater
Water by Culligan
(appearance may vary)
With adapter
Without adapter
About the automatic icemaker.
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Icemaker
Feeler Arm
Power Switch
Automatic Icemaker
(on some models)
When the refrigerator has been connected to
the water supply, slide the power switch to the
ON
position.
The icemaker will fill with water when 
it cools to 15°F. When the bin fills to the level
of  the feeler arm, the icemaker will stop
producing ice.
Be sure nothing interferes with the sweep of  the
feeler arm.
Throw away the first few batches of  ice to allow
the water line to clear.
The icemaker will produce seven cubes per
cycle—approximately 100–130 cubes in a 24-
hour period, depending on freezer
compartment temperature, room
temperature, number of  door openings and
other use conditions. 
You will hear a buzzing sound each time the
icemaker fills with water.
7