Olympus FE-20 Introduction Manual
----
-- -- -- --
X
Y
M
Y M D
D TIME
MENU
CANCEL
41
EN
Usage Tips
If the camera does not work as intended, or if
an error message is displayed on the screen,
and you are unsure of what to do, refer to the
information below to fi x the problem(s).
an error message is displayed on the screen,
and you are unsure of what to do, refer to the
information below to fi x the problem(s).
Troubleshooting
Battery
“The camera does not work even when
batteries are installed”.
batteries are installed”.
Insert recharged batteries in the correct direction.
“Charging the battery” (p. 10), “Loading the
battery (supplied) and the xD-Picture Card
battery (supplied) and the xD-Picture Card
TM
(sold separately) into the camera” (p. 11)
Battery performance may have been reduced
temporarily due to low temperature. Take the
batteries out of the camera, and warm them by
putting them in your pocket for a while.
temporarily due to low temperature. Take the
batteries out of the camera, and warm them by
putting them in your pocket for a while.
Card/Internal memory
“An error message is displayed”.
“Error message” (p. 42)
Shutter button
“No picture is taken when the shutter
button is pressed”.
button is pressed”.
Cancel sleep mode.
To save battery power, the camera automatically
goes into sleep mode and the monitor turns off
if there is no operation for 3 minutes when the
camera is turned on. No picture is taken even if
the shutter button is fully pressed in this mode.
Operate the zoom buttons or other buttons to
restore the camera from sleep mode before taking
a picture. If the camera is left for another 12
minutes, it automatically turns off. Press o to
turn the camera on.
To save battery power, the camera automatically
goes into sleep mode and the monitor turns off
if there is no operation for 3 minutes when the
camera is turned on. No picture is taken even if
the shutter button is fully pressed in this mode.
Operate the zoom buttons or other buttons to
restore the camera from sleep mode before taking
a picture. If the camera is left for another 12
minutes, it automatically turns off. Press o to
turn the camera on.
Press
n/K button to set a shooting mode.
Wait until
#(fl ash charge) stops blinking before
taking pictures.
●
●
●
●
●
●
Monitor
“Diffi cult to see”.
Condensation
*1
may have occurred. Turn off the
power, and wait for the camera body to become
acclimated to the surrounding temperature and dry
out before taking pictures.
acclimated to the surrounding temperature and dry
out before taking pictures.
*1
Dew drops can form in the camera when it is
suddenly taken from a cold location into a warm,
humid room.
humid room.
“Vertical lines appear on the screen”.
This condition may occur when the camera is
pointed at an extremely bright subject under a
clear sky and so on. The lines do not appear,
however, in the fi nal image.
pointed at an extremely bright subject under a
clear sky and so on. The lines do not appear,
however, in the fi nal image.
“The light is caught in the picture”.
Shooting with fl ash in dark situations results in
an image with many fl ash refl ections on dust in
the air.
an image with many fl ash refl ections on dust in
the air.
Date and time function
“Date and time settings return to the
default setting”.
default setting”.
If the batteries are removed and left out of the
camera for about a day
camera for about a day
*2
, the date and time
settings return to the default setting, and must
be reset.
be reset.
*2
The time until the date and time settings return
to the default setting varies depending on how
long the batteries have been loaded.
long the batteries have been loaded.
“Setting the date and time” (p. 13)
●
●
●
●
book_FE360_en.indb 41
book_FE360_en.indb 41
6/23/2008 5:28:01 PM
6/23/2008 5:28:01 PM