Pioneer axm-p8000 Installation Instruction

•

Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
properly.

•

Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.

•

Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.

•

Install the unit where it does not get in the dri-
ver’s way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.

•

Thoroughly wipe off the surface before affixing
the velcro tape.

Velcro tape
(soft surface)

Dashboard or
console

Display unit

Velcro tape (rough surface)

Drill 2 to 2.5 mm diameter holes.

Dashboard or
console

Double faced tape

Tapping screw

Bracket (B)

Binding screw

Washer

Display unit

Screw

Bracket (A)

<KSNNF> <04E00000>

Printed in Japan

<CRD3882-

B> UC

This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit
est conforme à CEMA.

•

Thoroughly wipe off the surface before affixing
the double faced tape.

•

Thoroughly wipe off the surface before affixing
the velcro tape.

Car mat or chassis

Hide-away unit

Velcro tape

Dashboard or console

Display unit

Double faced tape

•

This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.

•

To avoid shorts in the electrical system, be sure
to disconnect the ≠ battery cable before begin-
ning installation.

•

Refer to the owner’s manual for details on con-
necting the power amp and other units, then
make connections correctly.

•

Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.

•

Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.

•

Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.

•

Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.

•

Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.

•

When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.

•

To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a pos-
sibility of short-circuiting if the leads are not
insulated.

•

To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.

•

If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.

•

The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.

•

Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
manuals of both products and connect cords that
have the same function.

ACC position

No ACC position