Pioneer VSX-21TXH User Guide
Additional information
12
99
En
No sound
AMP ERR blinks in the display,
then the power automatically
switches off. The ADVANCED
MCACC blinks and the power
does not turn on.
then the power automatically
switches off. The ADVANCED
MCACC blinks and the power
does not turn on.
• The receiver may have a serious problem. Do not try switching the receiver on. Unplug the receiver
from the wall and call a Pioneer authorized independent service company.
from the wall and call a Pioneer authorized independent service company.
The ADVANCED MCACC
indicator flashes and power
turns off.
indicator flashes and power
turns off.
• There is a problem with the receiver’s power unit. The receiver may have a serious problem. Unplug
the receiver from the wall and call a Pioneer authorized independent service company.
the receiver from the wall and call a Pioneer authorized independent service company.
AMP OVERHEAT and the
power indicator flash and the
power turns off.
power indicator flash and the
power turns off.
• Allow the unit to cool down in a well-ventilated place before switching back on.
• Wait at least 1 minute, then try turning the power on again.
• Wait at least 1 minute, then try turning the power on again.
The Receiver suddenly power
off or the blue indicator at the
center of the receiver flashes.
off or the blue indicator at the
center of the receiver flashes.
• The power unit is damaged. Unplug the receiver from the wall and call a Pioneer authorized
independent service company.
independent service company.
Display blinks 12V TRG ERR.
• An error has arisen in the 12 V trigger jacks. Reconnect accurately then turn the power back on.
Symptom
Remedy
No sound is output when an
input function is selected.
No sound output from the front
speakers.
input function is selected.
No sound output from the front
speakers.
• Check the volume, mute setting (press MUTE) and speaker setting (press SPEAKERS).
• Make sure the correct input function is selected.
• Check that the MCACC setup microphone is disconnected.
• Make sure the correct input signal is selected (press SIGNAL SEL). Note that when PCM is
selected, you won’t be able to hear any other signal format.
• Check that the source component is connected properly (see Connecting your equipment on
page 15).
• Check that the speakers are connected properly (see Connecting the speakers on page 19).
• Make sure the correct input function is selected.
• Check that the MCACC setup microphone is disconnected.
• Make sure the correct input signal is selected (press SIGNAL SEL). Note that when PCM is
selected, you won’t be able to hear any other signal format.
• Check that the source component is connected properly (see Connecting your equipment on
page 15).
• Check that the speakers are connected properly (see Connecting the speakers on page 19).
No sound from the surround or
center speakers.
center speakers.
• Check that the Stereo listening mode or the Front Stage Surround Advance mode isn’t selected;
select one of the surround listening modes (see Listening in surround sound on page 56).
• Check that the surround/center speakers are not set to NO (see Speaker Setting on page 91).
• Check the channel level settings (see Channel Level on page 92).
• Check the speaker connections (see Connecting the speakers on page 19).
select one of the surround listening modes (see Listening in surround sound on page 56).
• Check that the surround/center speakers are not set to NO (see Speaker Setting on page 91).
• Check the channel level settings (see Channel Level on page 92).
• Check the speaker connections (see Connecting the speakers on page 19).
No sound from surround back
speakers.
speakers.
• Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on
page 91).
• Make sure surround back channel processing is set to SBch ON (see Using surround back channel
processing on page 59).
• If the source is Dolby Surround EX or DTS-ES with no flag to indicate 6.1 compatibility, then with
surround back channel processing set to SBch Auto, there will be no sound from the surround back
speakers. In this case, set to SBch ON (see Using surround back channel processing on page 59).
• If the source does not have 6.1 playback channels, make sure that surround back channel
processing is set to SBch ON and a surround mode is selected (see Listening in surround sound on
page 56).
• Check the speaker connections (see Connecting the speakers on page 19).
If only one surround back speaker is connected, make sure it’s connected to the left channel speaker
terminal.
page 91).
• Make sure surround back channel processing is set to SBch ON (see Using surround back channel
processing on page 59).
• If the source is Dolby Surround EX or DTS-ES with no flag to indicate 6.1 compatibility, then with
surround back channel processing set to SBch Auto, there will be no sound from the surround back
speakers. In this case, set to SBch ON (see Using surround back channel processing on page 59).
• If the source does not have 6.1 playback channels, make sure that surround back channel
processing is set to SBch ON and a surround mode is selected (see Listening in surround sound on
page 56).
• Check the speaker connections (see Connecting the speakers on page 19).
If only one surround back speaker is connected, make sure it’s connected to the left channel speaker
terminal.
No sound from subwoofer.
• Check that the subwoofer is connected properly, switched on and the volume turned up.
• If your subwoofer has a sleep function, make sure it is switched off.
• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 91).
• The crossover frequency may be set too low; try setting it higher to match the characteristics of
your other speakers (see Speaker Setting on page 91).
• If there is very little low frequency information in the source material, change your speaker settings
to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on
page 91).
• Check that the LFE channel is not set to OFF, or a very quiet setting (see Setting the Audio options
on page 66).
• Check the speaker level settings (see Channel Level on page 92).
• If your subwoofer has a sleep function, make sure it is switched off.
• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 91).
• The crossover frequency may be set too low; try setting it higher to match the characteristics of
your other speakers (see Speaker Setting on page 91).
• If there is very little low frequency information in the source material, change your speaker settings
to Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on
page 91).
• Check that the LFE channel is not set to OFF, or a very quiet setting (see Setting the Audio options
on page 66).
• Check the speaker level settings (see Channel Level on page 92).
Symptom
Remedy
VSX-23TXH_CUXJ.book 99 ページ ２００９年５月８日 金曜日 午前１０時４５分