Pioneer VSX-21TXH User Guide
Connecting your equipment
03
36
En
Switching components on and off using
the 12 volt trigger
the 12 volt trigger
You can connect components in your system (such as a
screen or projector) to this receiver so that they switch on
or off using 12 volt triggers when you select an input
function. However, you must specify which input
functions switch on the trigger using the The Input Setup
menu on page 43. Note that this will only work with
components that have a standby mode.
screen or projector) to this receiver so that they switch on
or off using 12 volt triggers when you select an input
function. However, you must specify which input
functions switch on the trigger using the The Input Setup
menu on page 43. Note that this will only work with
components that have a standby mode.
1
•
Connect the 12 V TRIGGER jack of this receiver to
the 12 V trigger of another component.
Use a cable with a mono mini-plug on each end for the
connection.
Use a cable with a mono mini-plug on each end for the
connection.
• The trigger maximum power is DC OUT 12 V/50 mA.
After you’ve specified the input functions that will switch
on the trigger, you’ll be able to switch the component on
or off just by pressing the input function(s) you’ve set on
page 43.
on the trigger, you’ll be able to switch the component on
or off just by pressing the input function(s) you’ve set on
page 43.
Connecting a PC for Advanced MCACC
output
output
When using Auto MCACC (page 78) or Acoustic
Calibration EQ Professional (page 83) to calibrate the
reverb characteristics of your listening room, the 3D
graphs of the reverb characteristics in your listening
room (before and after calibration) can be checked on a
computer screen by connecting the receiver to the
computer and using a special application to transfer the
data. The various MCACC parameters can also be
checked on the computer.
Calibration EQ Professional (page 83) to calibrate the
reverb characteristics of your listening room, the 3D
graphs of the reverb characteristics in your listening
room (before and after calibration) can be checked on a
computer screen by connecting the receiver to the
computer and using a special application to transfer the
data. The various MCACC parameters can also be
checked on the computer.
Use a commercially-available RS-232C cable to connect
the RS-232C jack on your computer to the 9-pin RS-232C
jack on the back panel of this receiver (the cable must be
cross type, female–female).
the RS-232C jack on your computer to the 9-pin RS-232C
jack on the back panel of this receiver (the cable must be
cross type, female–female).
The software to output the results is available from the
support area of the Pioneer website (http://
www.pioneerelectronics.com/PUSA/
Home+Entertainment+Custom+Install). Instructions
for using the software are also available here. If you have
any questions regarding, please contact the Customer
Support Division of Pioneer.
support area of the Pioneer website (http://
www.pioneerelectronics.com/PUSA/
Home+Entertainment+Custom+Install). Instructions
for using the software are also available here. If you have
any questions regarding, please contact the Customer
Support Division of Pioneer.
Please make sure your system meets the following
requirements:
requirements:
• The computer must be a PC functioning with one of
the following operating systems: Microsoft
®
Windows
®
Vista Home Basic/Home Premium/
Ultimate SP1, Windows
®
XP Professional/Home
Edition SP3 or Windows
®
2000 Professional SP4.
• The monitor must have a display resolution of 800 x
600 dots (SVGA) or greater.
• The computer must be equipped with at least one RS-
232C port.
2
• System must have internet access.
Microsoft
®
, Windows
®
Vista, Windows
®
XP and Windows
®
2000 are
either registered trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
the United States and/or other countries.
Note
1 Triggered connections with up to two devices compatible with 12 volt triggers can be made with this receiver.
RS-232C
COMPONENT
VIDEO
HDMI
ZONE2
VIDEO
S-VIDEO
ASSIGNABLE
ASSIGNABLE
MONITOR
OUT
MONITOR
OUT
IN
Y
L
R
P
B
P
R
Y
P
B
P
R
Y
OUT
DVD
IN
TV/SAT
IN
VIDEO
DVR
IN
IN
OUT
ZONE3
OUT
P
B
P
R
1
IN
BD IN
1
IN
2
IN
OUT 1
OU
(KURO
LINK)
3
1
3
(DVD)
IN
2
(DVR)
CONTROL
IR
12 V TRIGGER
IN
IN
IN
OUT
OUT
1
2
1
2
(OUTPUT 12 V
TOTAL 50 mA MAX)
TOTAL 50 mA MAX)
12 V TRIGGER
INPUT
VSX-23TXH
2 Laptops and other computers not equipped with an RS-232C port can be connected via USB port using a commercially available USB to
RS-232C converter cable (USB to serial converter cable). For instructions on COM port connections and settings, contact the manufacturer
of your computer.
of your computer.
VSX-23TXH_CUXJ.book 36 ページ ２００９年５月８日 金曜日 午前１０時４５分