Epson CX11N Quick Setup Guide

Cover A

 

  

With Lang = XXXX selected, press the button.

  

Use the

or

button to select the desired language, then press 

the

button.

Paper Out appears in the LCD screen. Open the MP Tray and place a 
stack of up to 80 sheets of paper in the tray. Adjust the paper guide on 
the right so that it is snug against the stack. Then close the cover.

  

Press the 

 Setup button.

 

The Setup light turns on and the 
LCD screen shows Setup Mode 
for a few seconds, then changes 
to the Setup menu screen.

  

While Printer Settings is 
highlighted, press the

button.

  

While Information Menu is 
highlighted, press the

button.

While Status Sheet is highlighted, press the

button.

 

A Status Sheet is printed.

  

If you have the CX11NF, place the Status Sheet face up on the Auto 
Document Feeder.

 

If you have the CX11N, place the Status Sheet face down on the 
document table.

Press the 

 Copy button on the control panel to enter the Copy mode.

  

Press the   B&W Start button.

 

The Status Sheet is copied.

  See “CX11N as a Network Printer” for information on setting up the CX11N as 

a network printer.

  

Make sure the CX11N is not 
connected to your computer.

Note: If you see a screen like this, 
click Cancel and disconnect the 
USB cable. You cannot install your 
software that way.

  

Insert the Epson CD-ROM into the 
CD drive of your computer.

Make sure you close all other 
applications. When you see the 
following screen, click Continue.

  

Read the license agreement that 
appears and click Agree.

  

For the type of installation, 
select Local.

Note: The illustrations show the CX11NF, but the instructions apply to both the 
CX11N and CX11NF unless otherwise noted.

 

Check that you have the following:

 

•

 

4 toner cartridges (Cyan, Magenta, Yellow, Black)

•

 Photoconductor 

unit

•

 USB 

cable

•

 Power 

cord

•

 Documentation: 

Basics Guide, Fax Guide (CX11NF only)

•

 

3 software CD-ROMs

 

Select a location for the CX11N. Make sure you allow enough space  
around the product to ensure smooth operation.

 

a  36.2 in. (920 mm)

 

b   10.2 in. (258 mm)

 

c   34.2 in. (868 mm)

 

d   3.9 in. (100 mm)

 

e   11.8 in. (300 mm)

 

The optional 500-Sheet Paper Cassette Unit adds   

 

5.1 in. (130 mm) to the bottom of the CX11N.

 

Remove all the packing tape from the outside of 
the unit.

 

Raise the scanner unit, then open cover C  
and pull out the insert.

 

Close cover C and lower the scanner unit.

 

Open cover A and remove the foam  

 

insert. Then close the cover.

 

Open the document cover and remove  
the insert. Then unlock the carriage lock.

 

Close the document cover.

Cover C

Connect the power cord to the 
CX11N and to an AC outlet.

Push the power switch to On.

Caution: Make sure the CX11N is turned on before installing the toner 
cartridges. Do not install the photoconductor before installing the toner 
cartridges.

 

Open cover A and remove the 
tape and plastic insert.

 

In the LCD screen the message 
Install [X] Toner Cartridge 
appears, where [X] is one of 
the following:

 

•

   Y: Yellow

•

   M: Magenta

•

   C: Cyan

•

   K: Black

 

Remove the toner cartridge from its 
package and gently shake it.

Warning: Do not touch the toner. Keep 
the toner away from your eyes. If toner 
gets on your skin or clothes, wash it off 
with soap and water immediately.

 

Hold the tag and gently pull the toner seal 
until it comes completely out.

 

Slide the toner cartridge into the tracks inside the printer. Push evenly on 
both sides until the cartridge stops securely in its slot.

 

If the cartridge doesn’t 
seem to be installed fully, 
remove it and reinstall it.

Caution: Don’t force the 
cartridge into the printer 
or force the lock lever 
down, or you may damage 
the printer.

 

Push down the lever to 
lock the toner cartridge.

Note: The toner cartridge 
is installed securely when 
you cannot turn the lock 
lever any further.

 

Close cover A and confirm the message in the LCD screen.

 

The LCD screen will display the next cartridge that needs to be 
installed. Open cover A and repeat steps 3 to 7 for each of the 
remaining toner cartridges.

Caution: Make sure the CX11N is turned on and you have installed all the toner 
cartridges, as described in the previous section.

 

Install Photoconductor appears in the LCD screen. Lift up the scanner.

 

Lift up cover B and raise the orange lever 
inside, on the right.

 

Remove the photoconductor from its package 
and pull off the protective sheet.

Caution: Do not touch the belt on the top
of the photoconductor or the blue roller beneath
it; otherwise, print quality may decrease.

Avoid exposing the photoconductor to light any longer than necessary.

Do not touch any other components inside the CX11N.

 

Hold the photoconductor by 
its handle and insert it into the 
slots marked with blue arrows 
inside the CX11N. Push it in 
until it clicks into place.

 

Flip down the orange lever, 
then close cover B.

 

Pull out the extension tray if necessary. Lower the scanner unit to its 
original position.

  

Select the Country: Press the

or

button to select the country, 

then press the

button.

  

Select the Language: Press the

or

button to select the language, 

then press the

button.

    Set the Date and Time: Press the

or

button to select the year, 

month, day, hour, and minute. Press the

button after selecting each 

item. The CX11NF then resets itself and reboots.

    Turn off the CX11NF.

  

Connect an RJ-11 cord to 
the telephone line interface 
on the CX11NF and to the 
RJ-11 jack on the wall.

 

An RJ-11 cord is not 

included with the CX11NF.

Turn on the CX11NF. 

  

Press the 

 Setup button. 

    

   

The Setup light turns on and the LCD screen shows Setup Mode for a 
few seconds, then changes to the Setup menu screen.

  

Press the ▼ button until Printer Settings is selected, then press the 

▲

 button.

  

Press the ▼ button until Setup Menu is selected, then press the 

▲

 button.