Epson 7850p Product Datasheet
EPSON PowerLite 7850p Projector
18
-
EPSON PowerLite 7850p Projector
6/03
If you’re using a network management utility running SNMP,
you can configure your network to send trap alerts even without a
plug-n. See the User’s Guide for more information.
you can configure your network to send trap alerts even without a
plug-n. See the User’s Guide for more information.
Make sure you have installed the EMP Monitor software
(included on the projector’s CD-ROM) on the computer you
want to use to monitor your projectors. (See the User’s Guide
for instructions.)
(included on the projector’s CD-ROM) on the computer you
want to use to monitor your projectors. (See the User’s Guide
for instructions.)
Note: Your computer must be running Microsoft Windows XP,
2000, Me or 98.
2000, Me or 98.
Setting Up the Projector on a Wired Network
This section explains how to configure projectors on a wired
network. You can also configure projectors for wireless
communication. See “Configuring the Connection” on
page 12 for details.
network. You can also configure projectors for wireless
communication. See “Configuring the Connection” on
page 12 for details.
1. Insert the PCMCIA LAN card into the card slot on the
back of the projector. Then connect the projector to your
network using a commercially available 100baseTX or
10baseT network cable.
network using a commercially available 100baseTX or
10baseT network cable.
2. Turn on the projector.
3. Press the
Menu
button on the remote control and select
Network
from the
Advanced2
menu.
4. If your network assigns addresses automatically, turn on
DHCP
.
If your network does not assign addresses automatically,
turn off
turn off
DHCP
and enter the projector’s
IP
Address
,
Subnet Mask
,
Gateway Address
, and
MAC Address
, as
needed.
❏ To enter numbers using the remote control, press the
❏ To enter numbers using the remote control, press the
Num
button until it lights, then use the numeric
keypad.
❏ To change the network addresses from the projector’s
control panel, press the right and left arrow buttons to
select the part of the address you want to enter, then
use the up and down arrow buttons to increase or
decrease the numeric value.
select the part of the address you want to enter, then
use the up and down arrow buttons to increase or
decrease the numeric value.
5. When you finish changing an address in the network menu,
press the
Enter
button (on the remote control) or the
Auto/Enter
button (on the projector). This stores the
value.
6. When you’re done making all necessary changes, press
ESC
to exit the menu system.
Opening and Closing EMP Monitor
To start EMP Monitor, click
Start > Programs or All
Programs > EPSON Projector > EMP Monitor
.
If you’ve added the program to the Startup programs folder, it
may already be open. If so, click the icon in the system tray on
the lower-right corner of your screen to display the EMP
Monitor window:
may already be open. If so, click the icon in the system tray on
the lower-right corner of your screen to display the EMP
Monitor window:
To close EMP Monitor, right-click the program icon shown
above, then select
above, then select
Exit
.
Brightness Control
Brightness Control
High
High
Low
Low
:
Video
Video
Audio
Audio
Setting
Setting
User's Logo
User's Logo
Advanced1
Advanced1
About
About
Reset All
Reset All
Projector ID
Projector ID
Network
Network
Reset
Reset
Execute
Execute
: 1
: 1
[Menu]: Exit
[Menu]: Exit
[ ]: Enter
[ ]: Enter
[ ]: Select
[ ]: Select
Effect
Effect
Advanced2
Advanced2
COM Port
COM Port
BNC Sync Termination
BNC Sync Termination
:
ON
ON
OFF
OFF
:
Set
Set
Set
Set
RS-232C
RS-232C
USB
USB
Auto setup
Auto setup
ON
ON
OFF
OFF
:
Select
Network
Network
Num button
Zero
Increase or
decrease
the value
decrease
the value
Select the part of the
address to change
address to change
Click here to start EMP Monitor