Lorex dgn209 User Manual
15
Motion Trigger Record
1. Press
ENTER to confirm MOTION TRIGGER RECORD setup.
2. Press▲ / ▼ to toggle the option between ON and OFF.
1. Select “ON” to set up the motion trigger recording: It can automatically switch from stand-by mode to Recording Mode.
The motion detection will change the scanning sequence and show “D” on the monitor.
NOTE: The trigger recording time will depend on the ALARM DURATION mode setting. It will record from the last trigger
time. For example, when the alarm duration setting is 1 min, the time recording time is from 9:00:00 to 9:01:00.
If the motion detection trigged again at 9:00:40, the triggered recording time will from 9:00:00 to 9:00:40 and
9:00:40 to 9:01:40. The total recording time is 00:01:40.
2. Select ”OFF”: The screen shows the motion detection and will change the scanning sequence while in the recording
mode and show “M” on the monitor.
The motion detection will change the scanning sequence and show “D” on the monitor.
NOTE: The trigger recording time will depend on the ALARM DURATION mode setting. It will record from the last trigger
time. For example, when the alarm duration setting is 1 min, the time recording time is from 9:00:00 to 9:01:00.
If the motion detection trigged again at 9:00:40, the triggered recording time will from 9:00:00 to 9:00:40 and
9:00:40 to 9:01:40. The total recording time is 00:01:40.
2. Select ”OFF”: The screen shows the motion detection and will change the scanning sequence while in the recording
mode and show “M” on the monitor.
Camera Channel Setup
To access the Camera option, press MENU followed by the 4-digit password. Use the ▲ / ▼ to scroll to the Camera option
and press ENTER.
and press ENTER.
TITLE
DWELL
ALARM
RECORD
---01 ON 5
5
5 LOW
EVENT
---02 ON 5
5
5 LOW
EVENT
---03 ON 5
5
5 LOW
EVENT
---04 ON 5
5
5 LOW
EVENT
The options available in this section are as follows:
Title
This feature is used to assign a 6-character title to each camera input.
1. Press
▲ / ▼ to select the desired time camera channel (1-9), and then press ENTER.
2. Press
▲ / ▼ to select the desired character and ◄ / ►to move to the next character
3. Press
MENU to confirm and exit the Title setting.
4. Press
MENU again to exit the Camera Setup Option.
Dwell
This feature is used to enable or disable the dwell feature for each camera when viewing using the call monitor output.
1. Press
▲ / ▼ to select the desired time camera channel (1-9), then press ENTER.
2. Press
◄ / ► to select the Dwell feature on the screen.
3. Press
MENU to confirm and exit the dwell setting.
4. Press
MENU again to exit the Camera Setup Option.
Brightness / Contrast / Color
This feature is used to adjust the video settings on each channel.
1. Press
▲ / ▼ to select the desired time camera channel (1-9), then press ENTER.
2. Press
◄ / ► to select the Brightness, Contrast, or Color feature on the screen.
3. Press
▲ / ▼ to select 0~9 on the screen.
4. Press
MENU to confirm and exit the Brightness, Contrast, or Color control feature
5. Press
MENU again to exit the Camera Setup Option.
Alarm Polarity
This feature is used to select the alarm polarity as LOW / OFF / HIGH.
1. Press
▲ / ▼ to select the desired time camera channel (1-9), then press ENTER.
2. Press
◄ / ► to select the Alarm Polarity feature on the screen.
3. Press
▲ / ▼ to select LOW / OFF / HIGH on the screen.
4. Press
MENU to confirm and exit the Alarm Polarity feature
5. Press
MENU again to exit the Camera Setup Option.