Cisco 2-port E&M voice/fax VIC3-2E/M= Data Sheet
Product codes
VIC3-2E/M=
Data Sheet
© 2009-2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 12
Table 3.
VIC/VWIC Options for the IPC High-Density Digital Voice Network Modules
VIC/VWIC Options
for the IPC High-
Density Digital
Voice NM
for the IPC High-
Density Digital
Voice NM
Description
Application
VIC3-2FXS/DID
2-port FXS/DID voice/fax interface card.
FXS port is used to connect directly to phones, fax machines, and key systems.
Generates battery polarity reversal and caller ID.
Generates battery polarity reversal and caller ID.
DID port is used to provide off-premises DID connection from central office.
Serves only incoming calls from the PSTN. Does not support caller ID in DID
mode.
Serves only incoming calls from the PSTN. Does not support caller ID in DID
mode.
VIC3-2FXS-E/DID
2-port Enhanced FXS/DID voice/fax interface
card.
card.
FXS port is used to connect directly to phones, fax machines, and key systems.
Generates battery polarity reversal and caller ID. VIC3-2FXS-E/DID
is designated as an “Off-Premise Extension Lite” product offering. This means
that while the module addresses a subset of the off-premise extension
applications, it should be noted that the module is not in full compliance
for off-premise usage.
Generates battery polarity reversal and caller ID. VIC3-2FXS-E/DID
is designated as an “Off-Premise Extension Lite” product offering. This means
that while the module addresses a subset of the off-premise extension
applications, it should be noted that the module is not in full compliance
for off-premise usage.
DID port is used to provide off-premises DID connection from central office.
Serves only incoming calls from the PSTN. Does not support caller ID in DID
mode.
Serves only incoming calls from the PSTN. Does not support caller ID in DID
mode.
VIC3-4FXS/DID
4-port FXS/DID voice/fax interface card
FXS port is used to connect directly to phones, fax machines, and key systems.
Generates battery polarity reversal and caller ID.
Generates battery polarity reversal and caller ID.
DID port is used to provide off-premises DID connection from central office.
Serves only incoming calls from the PSTN. Does not support caller ID in DID
mode.
Serves only incoming calls from the PSTN. Does not support caller ID in DID
mode.
VIC2-2FXO
2-port FXO voice/fax interface card
[universal card for all countries]. Also
supports analog Centralized Automated
Message Accounting (CAMA) on any port.
[universal card for all countries]. Also
supports analog Centralized Automated
Message Accounting (CAMA) on any port.
FXO port is used to connect to PBX or key system, or to provide off-premise
connections to PSTN. Supports battery reversal detection and caller ID. These
VICs can be software configured to work in all countries. Also used to connect
to analog CAMA trunk to provide dedicated E-911 service (North America only).
connections to PSTN. Supports battery reversal detection and caller ID. These
VICs can be software configured to work in all countries. Also used to connect
to analog CAMA trunk to provide dedicated E-911 service (North America only).
VIC2-4FXO
4-port FXO voice/fax interface card
[universal card for all countries]. Also
supports analog CAMA on any port.
[universal card for all countries]. Also
supports analog CAMA on any port.
FXO port is used to connect to PBX or key system, or to provide off-premise
connections to PSTN or PTT. Supports battery reversal detection and caller ID.
These VICs can be software configured to work in all countries. Also used to
connect to analog CAMA trunk to provide dedicated E-911 service (North
America only).
connections to PSTN or PTT. Supports battery reversal detection and caller ID.
These VICs can be software configured to work in all countries. Also used to
connect to analog CAMA trunk to provide dedicated E-911 service (North
America only).
VIC3-2E/M
2-port E&M voice/fax interface card
Use to connect to PBX or key system as tie lines.
VIC2-2BRI-NT/TE
2-port BRI voice/fax interface card
(configurable for either network or terminal
side)
(configurable for either network or terminal
side)
Use to connect as network side or user side to PBX or key system as off-
premise connections (ISDN voice BRI). Supports Patent Pending flexible L2 and
L3 configurations
premise connections (ISDN voice BRI). Supports Patent Pending flexible L2 and
L3 configurations
VWIC2-1MFT-T1/E1
1-Port T1/E1 Multiflex Trunk Voice/WAN
Interface Card
Interface Card
Used to connect to PBX, PSTN, or WAN using T1/E1 standard interface and
provide channel drop-and-insert capability.
provide channel drop-and-insert capability.
VWIC2-2MFT-T1/E1
2-Port T1/E1 Multiflex Trunk Voice/WAN
Interface Card
Interface Card
Used to connect to PBX, PSTN, or WAN using T1/E1 standard interface and
provide channel drop-and-insert capability.
provide channel drop-and-insert capability.
VWIC2-1MFT-G703
1-Port G.703 Multiflex Trunk Voice/WAN
Interface Card
Interface Card
Used to support unstructured E1 (G.703) and all features of the other Cisco
MFT VWIC2 modules, including drop-and-insert.
MFT VWIC2 modules, including drop-and-insert.
VWIC2-2MFT-G703
2-Port G.703 Multiflex Trunk Voice/WAN
Interface Card
Interface Card
Used to support unstructured E1 (G.703) and all features of the other Cisco
MFT VWIC2 modules, including drop-and-insert. Additional flexibility is provided
on the two port module with the capability to configure one port for unstructured
E1 (G.703) while configuring the other for standard framed E1.
MFT VWIC2 modules, including drop-and-insert. Additional flexibility is provided
on the two port module with the capability to configure one port for unstructured
E1 (G.703) while configuring the other for standard framed E1.