Sony CPD-300SF Manual

11

This section may help you isolate a problem and as a result,
eliminate the need to contact technical support, allowing
continued productivity.

/

If neither the u (power) indicator nor the
POWER SAVING indicator is lit
— Check that the power cord is properly

connected.

— Check that the u power switch is in the

“on” position.

/

If the POWER SAVING indicator is lit
— Check that your computer power switch is

in the “on” position.

— The monitor will recover when you press

any key on the keyboard of the computer.

— Check that the video cable is properly

connected. (If your computer is a
Macintosh system, the Macintosh adapter
(supplied) is required.)

— Check that the 5 BNC's are connected in the

right order (from power cord side: Red-
Green-Blue-HD-VD).

— Ensure that no pins are bent or pushed in

the HD15 connector of the cable.

— Check that the video card is seated

completely in a proper bus slot.

— Check that the video frequency range is

within that specified for the monitor.

— If using a Macintosh system, check that the

Macintosh adapter and the video signal
cable are properly connected.

/

If your system is the Windows 95
— Even if you select SONY for the maker on

the device select screen, the model name
(CPD-300SFT) may not appear.
In this case, select the DDC standard
monitor.

/

If the u (power) and/or the POWER SAVING
indicators are both flashing
— Turn the monitor off and on. If the

indicators are not both flashing, the
monitor is in the normal condition. If the
indicator is still flashing, there is a potential
monitor failure.

/

If you do the above procedures and the
monitor does not recover
— Unplug the video cable, then press and

hold the ¨ + button for 2 seconds to
display the color bars. If the color bars
appear, the monitor is in the normal
condition. Then turn the monitor off and on
by pressing the u power switch to return
the monitor to the normal condition.
If the color bars do not appear, there is a
potential monitor failure.

/

If your computer is a Macintosh system and
the Macintosh adapter has micro switches
— Check that the micro switches are properly

set for your system. (See the adapter
manual.)

Picture tube

0.30 mm aperture grille pitch
20␣ inches measured diagonally
90-degree deflection

Viewable image size

Approx. 388 

×

 292 mm (w/h)

(15 

3

/

8 

×

 11 

1

/

2

 inches)

19.1” viewing image

Resolution

Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines

Standard image area Approx. 373 

×

 280 mm (w/h)

(14 

3

/

4

 

×

 11 

1

/

8

 inches)

or
Approx. 350 

×

 280 mm (w/h)

(13 

7

/

8

 

×

 11 

1

/

8

 inches)

Deflection frequency  Horizontal: 30 to 86 kHz

 Vertical: 48 to 150 Hz

AC input voltage/current

 100 to 120 V, 50/60 Hz, 1.7 A
 220 to 240 V, 50 – 60 Hz, 1.2 A

Power consumption  Max. 150 W
Dimensions

 Approx. 472 

×

 493.5 

×

 501 mm (w/h/d)

 (18 

5

/

8

 

×

 19 

1

/

2

 

×

 19 

3

/

4

 inches)

Mass

 Approx. 29.5 kg (65 lb 1 oz)

Video input 1 connector (HD15) (Female)
The cable accepts RGB video signals (0.714 Vp-p, positive)
and SYNC signals.

Pin No.

1

2

3

4

5

6

7

Signal

Red

Green
(Composite
Sync on Green)

Blue

—

DDC Ground*

Red Ground

Green Ground

Pin No.

8

9

10

11

12

13

14

15

Signal

Blue Ground

DDC + 5V*

Ground

—

Bi-Directional
Data (SDA)*

H. Sync

V. Sync

Data Clock (SCL)*

*

Display Data Channel (DDC) Standard by VESA.

Design and specifications are subject to change without
notice.