Sony RM-VZ220 Manual

4-170-642-12(1)

Remote Commander

RM-VZ220

Operating Instructions
Manual de instrucciones (parte posterior)

English

For the Customers in the U.S.A.
WARNING

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this

manual could void your authority to operate this equipment.

Setting Up the RM-VZ220

The RM-VZ220 is preset at the factory to operate Sony brand video devices

set to any of the Device Select buttons (see the table below).

To use with non-Sony devices, or Sony devices that are not preset at the

factory, set the manufacturer’s code for each device.

Devices

Button

Factory setting*

Sony TV (00810)

TV, Cable set top box, Satellite

receiver, IPTV, DVD player, DVD

recorder, Blu-ray Disc player, DVR

(digital video recorder), PVR

(personal video recorder), VCR,

DVD Home Theater

CBL (SAT)

Cable set top box (non-

Sony) (51376)

VCR

Sony VCR (60032)

DVD

Sony DVD player

(11033)

The five-digit code is the preset manufacturer’s code.

Note

Only a TV can be assigned to the TV Device Select button. You can assign any device to

the other Device Select buttons.

Installing the batteries

Slide open the battery compartment and insert two size AA (R6) dry

batteries (not supplied).

Insert the batteries (negative end first) through the guide clamp within each

compartment as shown below.

Battery life

Under normal conditions, size AA (LR6) alkaline batteries will last up to one

year. If the RM-VZ220 does not operate properly, the batteries might be

drained. Replace both batteries with new ones.

Notes

 Replace the batteries within 2 minutes after removing them, and do not press any

button when replacing the batteries. Otherwise, your code settings may be cleared.

 Do not use an old battery with a new one, or mix different types of batteries together.

 If the electrolyte inside the battery should leak, wipe the contaminated area of the

battery compartment with a cloth and replace the old batteries with new ones. To

prevent electrolyte from leaking, remove the batteries when you plan not to use the

RM-VZ220 for a long period of time.

Specifications

Operating distance

Approx. 11 m (36 ft) (varies depending on devices of

different manufacturers)

Power requirements

Two size AA (R6) dry batteries (not supplied)

Battery life

Approx. 1 year when using size AA (LR6) alkaline batteries

(varies depending on frequency of button use - up to approx.

300 times per day.)

Dimensions

Approx. 53 × 213 × 27 mm (2

× 8

× 1

in.)

(w/h/d)

Mass

Approx. 100 g (3.5 oz) (not including batteries)

Design and specifications are subject to change without notice.

Troubleshooting

If you have problems setting up or using the RM-VZ220:

 Carefully perform the setup procedure of “Startup Guide.” If the RM-VZ220 does not

work, try repeating the setup procedure using another manufacturer’s code (if listed

for your device). If you still cannot operate the RM-VZ220, try the Search function

(see “Searching for the correct code”).

 Aim the RM-VZ220 directly at the device.

 Remove any obstacles in the path between the RM-VZ220 and the device.

 Make sure you have pressed the correct Device Select button.

 Check that the device has infrared remote capability. For example, if your device did

not come with a remote control, it probably is not capable of being controlled by the

RM-VZ220.

 The batteries are weak, or not inserted correctly. Replace them with new ones or insert

them correctly.

For the customers in the U.S.A.

Customer Support Information

After you have read through this manual, if you still cannot get the RM-VZ220 to work

properly, call the Sony Customer Support Helpline at

1-800-822-2217.

Startup Guide

This guide shows you how to set up and use the RM-VZ220 to operate your devices.

If your Sony device has already been preset, see “Operate the device.”

Set the manufacturer’s code

Example: To set up a Philips TV

Find the manufacturer’s code in “Manufacturer’s Code List.”

RM-VZ220_U [US,ES] 4-170-642-12(1)

4-170-642-12(1)

Remote Commander
RM-VZ220