Sony RMT-D165A Manual
70
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs.
Should any problem persist, consult your
nearest Sony dealer (for customers in the
USA only).
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs.
Should any problem persist, consult your
nearest Sony dealer (for customers in the
USA only).
Power
The power is not turned on.
, Check that the AC power cord is connected
securely.
Picture
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 18)
, The connecting cords are damaged.
, Check the connection to your TV (page 18)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
that the signal from the player appears on
the TV screen.
, The disc is dirty or flawed.
, If the picture output from your player goes
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programs could affect
picture quality. If you still experience
problems even when you connect your
player directly to your TV, please try
connecting your player to your TV’s S
VIDEO input (page 18).
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programs could affect
picture quality. If you still experience
problems even when you connect your
player directly to your TV, please try
connecting your player to your TV’s S
VIDEO input (page 18).
, You set the NORMAL/PROGRESSIVE
switch to PROGRESSIVE on the rear panel
(the PROGRESSIVE indicator lights up)
even though your TV cannot accept the
progressive signal. In this case, set the
NORMAL/PROGRESSIVE switch to
NORMAL on the rear panel so that the
PROGRESSIVE indicator turns off.
(the PROGRESSIVE indicator lights up)
even though your TV cannot accept the
progressive signal. In this case, set the
NORMAL/PROGRESSIVE switch to
NORMAL on the rear panel so that the
PROGRESSIVE indicator turns off.
, You set the NORMAL/PROGRESSIVE
switch to PROGRESSIVE on the rear panel
(the PROGRESSIVE indicator lights up)
but did not connect your TV to the player’s
COMPONENT VIDEO OUT jacks using a
COMPONENT VIDEO cord. Set to the
PROGRESSIVE only when you connect
(the PROGRESSIVE indicator lights up)
but did not connect your TV to the player’s
COMPONENT VIDEO OUT jacks using a
COMPONENT VIDEO cord. Set to the
PROGRESSIVE only when you connect
, Even if your TV is compatible with
progressive format (480p) signals, the
image may be affected when you set the
player to progressive format. In this case,
set the NORMAL/PROGRESSIVE switch
to NORMAL so that the PROGRESSIVE
indicator turns off and the player is set to
normal (interlace) format.
image may be affected when you set the
player to progressive format. In this case,
set the NORMAL/PROGRESSIVE switch
to NORMAL so that the PROGRESSIVE
indicator turns off and the player is set to
normal (interlace) format.
Even though you set the aspect ratio in “TV
TYPE” of “SCREEN SETUP,” the picture
does not fill the screen.
TYPE” of “SCREEN SETUP,” the picture
does not fill the screen.
, The aspect ratio of the disc is fixed on your
DVD.
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
, The connecting cord is damaged.
, The player is connected to the wrong input
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (COAXIAL) jack,
check the audio settings (page 68).
check the audio settings (page 68).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
Sound distortion occurs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
“ON” (page 68).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” to “TV MODE” (page 68).
“AUDIO DRC” to “TV MODE” (page 68).
, Set “AUDIO ATT” in “AUDIO SETUP” to
“OFF” (page 68).