Sony XBR-52HX909 Manual
6
Setting up your TV
Some TV models are packaged with a detached
Table-Top Stand so you can mount your TV to a
wall right away. If you are not mounting the TV to
a wall, you will need to attach the Table-Top
Stand. You will need a Phillips screwdriver and
the supplied screws to complete the task. Look for
the supplied Table-Top Stand instruction leaflet.
Be sure to consider the following while setting
up your TV:
•
Table-Top Stand so you can mount your TV to a
wall right away. If you are not mounting the TV to
a wall, you will need to attach the Table-Top
Stand. You will need a Phillips screwdriver and
the supplied screws to complete the task. Look for
the supplied Table-Top Stand instruction leaflet.
Be sure to consider the following while setting
up your TV:
•
Disconnect all cables when carrying the TV.
•
Carry the TV with the adequate number of
people; larger size TVs require two or more
people.
people; larger size TVs require two or more
people.
•
Correct hand placement while carrying the
TV is very important for safety and to avoid
damage.
TV is very important for safety and to avoid
damage.
•
Ensure your TV has adequate ventilation,
see page 15.
see page 15.
•
For best picture quality, do not expose the
screen to direct illumination or sunlight.
screen to direct illumination or sunlight.
•
Avoid installing the TV in a room with
reflective wall and floor materials.
reflective wall and floor materials.
•
If the TV is brought directly from a cold to a
warm location, or is placed in a very damp
room, or is placed in a room in which heating
has just been turned on, moisture may
condense on the surface or inside the TV.
Should this occur, turn off the TV and leave the
TV off until the moisture evaporates, and then
the TV can be used. If you notice moisture
condensation between the glass panel and the
LCD, turn on the TV and the condensation will
evaporate after the TV has warmed up.
warm location, or is placed in a very damp
room, or is placed in a room in which heating
has just been turned on, moisture may
condense on the surface or inside the TV.
Should this occur, turn off the TV and leave the
TV off until the moisture evaporates, and then
the TV can be used. If you notice moisture
condensation between the glass panel and the
LCD, turn on the TV and the condensation will
evaporate after the TV has warmed up.
Attaching the Table-Top
Stand
Stand
Refer to the supplied Table-Top Stand
instruction leaflet for proper attachment for
some TV models.
instruction leaflet for proper attachment for
some TV models.
1
Gently slide the TV unit onto the
Table-Top Stand and align the screw
holes.
Table-Top Stand and align the screw
holes.
~
• Do not put stress on the LCD panel or the frame
around the screen.
• Be careful to not pinch your hands or the AC
power cord when you install the TV unit to the
Table-Top Stand.
Table-Top Stand.
2
Use the supplied screws to attach the
TV unit to the Table-Top Stand.
TV unit to the Table-Top Stand.
~
• If you use an electric screwdriver, set the
tightening torque at approximately 1.5 N·m
{15 kgf·cm}.
{15 kgf·cm}.
3
For XBR-52/46HX909 and
KDL-40HX800, after all the screws are
tighten cover the Table-Top Stand with
the supplied stand rear cover.
KDL-40HX800, after all the screws are
tighten cover the Table-Top Stand with
the supplied stand rear cover.
~
• You can attach the TV to the Table-Top Stand
with the stand rear cover on with the exception of
XBR-52/46HX909 and KDL-40HX800. XBR-52/
46HX909 and KDL-40HX800 must follow the
above instructions.
XBR-52/46HX909 and KDL-40HX800. XBR-52/
46HX909 and KDL-40HX800 must follow the
above instructions.
For XBR-52/46HX909 For KDL-55/46/40HX800