Sony HCD-X10 User Manual
Ad
v
v
a
nce
d
Sett
ings
and
Adjus
tme
nts
nts
masterpage:Right
specdef v20060111
filename[G:\FM\Sony\0605\DAVX10_US\Source\3210565131\3210565131DAVX10\gb12adv.fm]
model name [DAV-X10]
[3-210-565-13(1)]
83
US
x [AUDIO DRC] (DVD VIDEO only)
Narrows the dynamic range of the sound track.
Useful for watching movies at low volume late
at night.
Narrows the dynamic range of the sound track.
Useful for watching movies at low volume late
at night.
x [AUDIO (HDMI)]
Selects the type of audio signal output from the
HDMI OUT jack.
Selects the type of audio signal output from the
HDMI OUT jack.
Note
• A loud noise (or no sound) will be output if you
connect the system to a TV that is not compatible
with DOLBY DIGITAL/DTS (digital theater system)
signals and [AUTO] is selected. In this case, select
[PCM].
with DOLBY DIGITAL/DTS (digital theater system)
signals and [AUTO] is selected. In this case, select
[PCM].
• When you connect the system and TV with the HDMI
cable and [AUTO] or [PCM] is selected, AUDIO
DRC, A/V SYNC, TONE, MOVIE/MUSIC, and
sound field are not applied to the sound that is output
from the TV.
DRC, A/V SYNC, TONE, MOVIE/MUSIC, and
sound field are not applied to the sound that is output
from the TV.
Returning the settings on the
Setup Display to the default
Setup Display to the default
1
Select [RESET] in Step 4 of “Using the
Setup Display” (page 78) and press
Setup Display” (page 78) and press
.
2
Select [YES] using
X/x.
You can also quit the process and return to
the Control Menu by selecting [NO] here.
the Control Menu by selecting [NO] here.
3
Press .
All the settings explained on pages 79 to 83
return to the default settings. Do not press
[/1 while resetting the system as it takes a
few seconds to complete.
return to the default settings. Do not press
[/1 while resetting the system as it takes a
few seconds to complete.
Note
• When you turn the system on after resetting and no
disc is in the unit, the guide message appears on the
TV screen. To perform the Quick Setup (page 18),
press
TV screen. To perform the Quick Setup (page 18),
press
, to return to normal screen, press CLEAR.
• “BASS,” “TREBLE,” (page 33) and “SW LEVEL”
(page 77) settings are also returned to the default.
Returning the sound field
settings or radio settings to
the default
settings or radio settings to
the default
1
Turn off the power.
2
Press and hold "/1 on the unit about 5
seconds.
seconds.
“MEMORY CLR” and “PUSH POWER”
appear alternately in the front panel display
about 10 seconds.
appear alternately in the front panel display
about 10 seconds.
3
Press "/1.
“CLEARING” appears in the front panel
display and the default settings are returned.
After “CLEARED!” appears, the system is
turned off.
display and the default settings are returned.
After “CLEARED!” appears, the system is
turned off.
Note
• In Step 3, if you do not press "/1 or press any buttons
other than "/1 on the unit, the system turns on. The
setting is not made.
setting is not made.
[OFF]
No compression of dynamic
range.
range.
[STANDARD]
Reproduces the sound track with
the kind of dynamic range that the
recording engineer intended.
the kind of dynamic range that the
recording engineer intended.
[MAX]
Compresses dynamic range fully.
[OFF]
The sound is not output from the
HDMI OUT jack.
HDMI OUT jack.
[AUTO]
Outputs audio signals that is
matched to the requested audio
stream from the connected TV.
matched to the requested audio
stream from the connected TV.
[PCM]
Converts Dolby Digital, DTS
(digital theater system), or 96
kHz/24 bit PCM (pulse code
modulation) signals to 48 kHz/ 16
bit PCM (pulse code modulation).
(digital theater system), or 96
kHz/24 bit PCM (pulse code
modulation) signals to 48 kHz/ 16
bit PCM (pulse code modulation).
Returning to the Default
Settings
Settings