Sony STR-K7000 Manual
78
US
C:\Documents and
Settings\pc13\Desktop\J9052007_2662265111HT7000DH_US\2662265111\US07REM_HT-
7000DH-U.fm
Settings\pc13\Desktop\J9052007_2662265111HT7000DH_US\2662265111\US07REM_HT-
7000DH-U.fm
masterpage: Left
HT-8000MH
2-662-265-11 (1)
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. Refer to the following
table to solve the problem. If any problem
persists, consult your nearest Sony dealer.
If an error message appears while you perform
Auto Calibration, see “Error and warning
codes” (page 32) to solve the problem.
message. You can check the condition of the
system by the message. Refer to the following
table to solve the problem. If any problem
persists, consult your nearest Sony dealer.
If an error message appears while you perform
Auto Calibration, see “Error and warning
codes” (page 32) to solve the problem.
DEC. EROR
Appears when a signal the receiver cannot
decode (ex. DTS-CD) is input and “DEC.
PRI.” on the AUDIO menu is set to “DEC.
PCM”. Set it to “DEC. AUTO” (page 41).
decode (ex. DTS-CD) is input and “DEC.
PRI.” on the AUDIO menu is set to “DEC.
PCM”. Set it to “DEC. AUTO” (page 41).
PROTECT
Irregular current is output from the
speakers. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
speakers. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
If you are unable to remedy the
problem using the
troubleshooting guide
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy
the problem (page 29). However, note that all
memorized settings will be reset to their
factory settings and you will have to readjust
all settings on the receiver.
the problem (page 29). However, note that all
memorized settings will be reset to their
factory settings and you will have to readjust
all settings on the receiver.
If the problem persist
Consult your nearest Sony dealer. Note that if
service personnel changes some parts during
repair, these parts may be retained.
service personnel changes some parts during
repair, these parts may be retained.
Reference sections for clearing
the receiver’s memory
the receiver’s memory
Specifications
AUDIO POWER
SPECIFICATIONS
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
HARMONIC DISTORTION:
(Models of area code U only)
With 6 ohm loads, both channels driven, from
120 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than
0.7% total harmonic distortion from 250
milliwatts to rated output.
With 6 ohm loads, both channels driven, from
120 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than
0.7% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
Power Output
1)
Models of area code U
(6 ohms 1 kHz, THD 10%)
FRONT
(6 ohms 1 kHz, THD 10%)
FRONT
2)
: 140
W/ch
CENTER
2)
: 140
W
SUR
2)
: 140
W/ch
Models of area code CA
(6 ohms 1 kHz, THD 0.7%)
FRONT
(6 ohms 1 kHz, THD 0.7%)
FRONT
2)
: 90
W/ch
CENTER
2)
: 90
W
SUR
2)
: 90
W/ch
(6 ohms 1 kHz, THD 10%)
FRONT
FRONT
2)
: 140
W/ch
CENTER
2)
: 140
W
SUR
2)
: 140
W/ch
1)
Measured under the following conditions:
2)
Depending on the sound field settings and the
source, there may be no sound output.
source, there may be no sound output.
Inputs (Analog)
To clear
See
All memorized settings
Customized sound fields
Area code
Power requirements
U, CA
120 V AC, 60 Hz
MULTI CH IN,
SA-CD/CD,
MD/TAPE, DVD,
VIDEO 1, 2, 3
VIDEO 1, 2, 3
Sensitivity: 800 mV
Impedance: 50 kohms
US01COV_HT-7000DH-U.book Page 78 Wednesday, January 25, 2006 3:30 PM