Sony XAV-63 Manual
59
Design and specifications are subject to change
without notice.
without notice.
Region code
The region system is used to protect software
copyrights.
The region code is located on the bottom of the unit,
and only DVDs labeled with an identical region code
can be played on this unit.
copyrights.
The region code is located on the bottom of the unit,
and only DVDs labeled with an identical region code
can be played on this unit.
DVDs labeled
can also be played.
If you try to play any other DVD, the message
“Playback prohibited by region code.” will appear on
the monitor screen. Depending on the DVD, no region
code may be labeled even though playing the DVD is
prohibited by area restrictions.
“Playback prohibited by region code.” will appear on
the monitor screen. Depending on the DVD, no region
code may be labeled even though playing the DVD is
prohibited by area restrictions.
System requirements for using
SensMe™
SensMe™
Computer
• CPU/RAM
– IBM PC/AT compatible machine
– CPU: Intel Pentium III Processor 450 MHz or
– CPU: Intel Pentium III Processor 450 MHz or
higher
– RAM: 256 MB or more (For Windows XP), 512
MB or more (For Windows Vista or later)
• USB port
OS
Windows XP, Windows Vista, Windows 7
For details on compatible editions or Service Packs,
visit the support site on the back cover.
For details on compatible editions or Service Packs,
visit the support site on the back cover.
Monitor
High color (16-bit) or more, 800
× 600 pixels or more
Other
Internet connection
Notes
• The following system environments are not
• The following system environments are not
supported.
– Non IBM PC type computers, such as Macintosh,
– Non IBM PC type computers, such as Macintosh,
etc.
– Homemade computers
– OS upgraded computers
– Multi-display environment
– Multi-boot environment
– Virtual machine environment
– OS upgraded computers
– Multi-display environment
– Multi-boot environment
– Virtual machine environment
• Depending on the computer condition, operation
may not be possible even with the recommended
environment.
environment.
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check the
connection and operating procedures.
problems you may encounter with your unit.
Before going through the checklist below, check the
connection and operating procedures.
If the problem is not solved, visit the support site on
the back cover.
the back cover.
US and foreign patents licensed from Dolby
Laboratories.
Laboratories.
MPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and Thomson.
patents licensed from Fraunhofer IIS and Thomson.
ALL
General
No power is being supplied to the unit.
• Check the connection or fuse.
• If the unit is turned off and the display disappears, it
• If the unit is turned off and the display disappears, it
cannot be operated with the remote commander (not
supplied).
supplied).
t Turn on the unit.
The power antenna (aerial) does not extend.
The power antenna (aerial) does not have a relay box.
There is no beep sound.
• The beep sound is canceled (page 44).
• An optional power amplifier is connected and you are
• An optional power amplifier is connected and you are
not using the built-in amplifier.
The contents of the memory have been erased.
• The reset button has been pressed.
t Store again into the memory.
• The power supply lead or battery has been
disconnected or it is not connected properly.
Stored stations and correct time are erased.
The fuse has blown.
The unit makes noise when the position of the
ignition is switched.
The fuse has blown.
The unit makes noise when the position of the
ignition is switched.
The leads are not matched correctly with the car’s
accessory power connector.
accessory power connector.
The display disappears from/does not appear
on the monitor.
on the monitor.
• The dimmer is set to “ON” (page 44).
• The display disappears if you press and hold
• The display disappears if you press and hold
(SOURCE/OFF).
t Press (SOURCE/OFF) on the unit until the
display appears.
• “M.OFF” is set to on and the Monitor Off function is
activated (page 12).
t Touch anywhere on the display to turn the display
back on.
The display does not respond to your touch
correctly.
correctly.
• Touch one part of the display at a time. If two or more
parts are touched simultaneously, the display will not
operate correctly.
operate correctly.
• Calibrate the touch panel of the display (page 42).
The Auto Off function does not operate.
The unit is turned on. The Auto Off function activates
after turning off the unit.
t Exit the source.
after turning off the unit.
t Exit the source.
Operation of the remote commander (not
supplied) is not possible.
supplied) is not possible.
If the Monitor Off function is activated (no lighting),
operation of the remote commander (not supplied) is
not possible (page 12).
operation of the remote commander (not supplied) is
not possible (page 12).