Sony CDX-1300FP Manual
Operating Instructions
Sony Corporation
2000
Printed in Japan
FM/AM
Compact Disc
Player
Compact Disc
Player
CDX-1300
For installation and connections, see the supplied installation/connections
manual.
manual.
Owner’s Record
The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this
product.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this
product.
Model No. CDX-1300 Serial No.
Welcome !
Thank you for purchasing the Sony Compact
Disc Player. This unit lets you enjoy a variety of
features.
Disc Player. This unit lets you enjoy a variety of
features.
Warning
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
receiver is connected.
— Consult the dealer or an experienced radio/
TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
CAUTION
The use of optical instruments with this product
will increase eye hazard.
will increase eye hazard.
Getting Started
Resetting the unit
Before operating the unit for the first time or
after replacing the car battery, you must reset
the unit.
Remove the front panel and press the reset
button with a pointed object, such as a ball-point
pen.
after replacing the car battery, you must reset
the unit.
Remove the front panel and press the reset
button with a pointed object, such as a ball-point
pen.
Notes
• Pressing the reset button will erase the clock
• Pressing the reset button will erase the clock
setting and some memorized program and
memory functions.
memory functions.
• When you connect the power supply cord to the
unit or reset the unit, wait for about 10 seconds
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and
you will have to press the reset button again.
before you insert a disc. If you insert a disc within
these 10 seconds, the unit will not be reset, and
you will have to press the reset button again.
Detaching the front panel
You can detach the front panel of this unit to
prevent the unit from being stolen.
prevent the unit from being stolen.
1
Press (OFF).
2
Press (RELEASE), then slide the front
panel a little to the left, and pull it off
towards you.
panel a little to the left, and pull it off
towards you.
Reset button
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
18 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than
1 % total harmonic distortion.
18 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more than
1 % total harmonic distortion.
Other specifications
CD player section
System
Compact disc digital audio
system
system
Signal-to-noise ratio
90 dB
Frequency response
10 – 20,000 Hz
Wow and flutter
Below measurable limit
Laser Diode Properties
Material
GaAs + GaAlAs
Wavelength
785 ~ 815 nm (Typ.800 nm)
Emission Duration
Continuous
Laser output power
Less than 0.5 mW*
* This output is the value measured at a distance of
0.7 mm from the objective lens surface on the
Optical Pick-up Block.
Optical Pick-up Block.
Tuner section
FM
Tuning range
Tuning range
87.5 – 107.9 MHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz
Usable sensitivity
12 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
65 dB (stereo),
68 dB (mono)
68 dB (mono)
Harmonic distortion at 1 kHz
0.7 % (stereo),
0.5 % (mono)
0.5 % (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
AM
Tuning range
Tuning range
530 – 1,710 kHz
Antenna terminal
External antenna connector
Intermediate frequency
10.7 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs
(sure seal connectors)
(sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output 45 W
×
4 (at 4 ohms)
General
Outputs
Audio output
Power amplifier control
Power antenna relay control
Power amplifier control
Power antenna relay control
Tone controls
Bass ±8 dB at 100 Hz
Treble ±8 dB at 10 kHz
Treble ±8 dB at 10 kHz
Power requirements
12 V DC car battery
(negative ground)
(negative ground)
Dimensions
Approx. 178
×
50
×
178 mm
(7
1
/
8
×
2
×
7
1
/
8
in.)
(w/h/d)
Mounting dimensions
Approx. 182
×
53
×
162 mm
(7
1
/
4
×
2
1
/
8
×
6
1
/
2
in.)
(w/h/d)
Mass
Approx. 1.2 kg (2 lb. 10 oz.)
Supplied accessories
Parts for installation and
connections (1 set)
connections (1 set)
Optional accessories
Compact disc single adapter
CSA-8
CSA-8
Design and specifications are subject to change
without notice.
without notice.
Additional Information
Precautions
• If your car was parked in direct sunlight
resulting in a considerable rise in temperature
inside the car, allow the unit to cool off before
operating it.
inside the car, allow the unit to cool off before
operating it.
• If no power is being supplied to the unit,
check the connections first. If everything is in
order, check the fuse.
order, check the fuse.
• If no sound comes from the speakers of a two-
speaker system, set the fader control to the
center position.
center position.
•If your car is equipped with a power antenna,
it will extend automatically while the unit is
operating.
operating.
If you have any questions or problems
concerning your unit that are not covered in this
manual, please consult your nearest Sony dealer.
concerning your unit that are not covered in this
manual, please consult your nearest Sony dealer.
Notes on handling CDs
A dirty or defective disc may cause sound
dropouts while playing. To enjoy optimum
sound, handle the disc by its edge. To keep the
disc clean, do not touch the surface.
dropouts while playing. To enjoy optimum
sound, handle the disc by its edge. To keep the
disc clean, do not touch the surface.
Do not stick paper or tape on the labeled surface.
Do not expose the discs to direct sunlight or heat
sources such as hot air-ducts, or leave them in a
car parked in direct sunlight where there can be
a considerable rise in temperature inside the car.
sources such as hot air-ducts, or leave them in a
car parked in direct sunlight where there can be
a considerable rise in temperature inside the car.
Before playing, clean the discs with an optional
cleaning cloth. Wipe each disc from the center
out.
Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic
spray intended for analog discs.
cleaning cloth. Wipe each disc from the center
out.
Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic
spray intended for analog discs.
Notes on discs
If you use the discs explained below, the sticky
residue can cause the CD to stop spinning and
may cause malfunction or ruin your discs.
residue can cause the CD to stop spinning and
may cause malfunction or ruin your discs.
Do not use second-hand or rental CDs that have
a sticky residue on the surface (for example from
peeled-off stickers or from ink, or glue leaking
from under the stickers).
a sticky residue on the surface (for example from
peeled-off stickers or from ink, or glue leaking
from under the stickers).
There are paste residue
Ink is sticky
Ink is sticky
Do not use rental CDs with old labels that are
beginning to peel off.
beginning to peel off.
Stickers that are beginning to
peel away, leaving a sticky
residue
peel away, leaving a sticky
residue
Do not use your CDs with labels or stickers
attached.
attached.
Labels are attached
Notes on CD-R discs
•You can play CD-Rs (recordable CDs) on this
unit. However depending on the conditions of
the recording equipment or the CD-R disc
itself, some CD-Rs cannot be played on this
unit.
the recording equipment or the CD-R disc
itself, some CD-Rs cannot be played on this
unit.
•You cannot play a CD-R that is not finalized
(Finalization is necessary for a recorded CD-R
disc to be played on the audio CD player).
disc to be played on the audio CD player).
•You cannot play CD-RWs (rewritable CDs) on
this player.
Notes on moisture condensation
On a rainy day or in a very damp area, moisture
may condense on the lenses inside the CD
player. Should this occur, the unit will not
operate properly. In this case, remove the disc
and wait for about an hour until the moisture
evaporates.
may condense on the lenses inside the CD
player. Should this occur, the unit will not
operate properly. In this case, remove the disc
and wait for about an hour until the moisture
evaporates.
When you play 8 cm (3 in.) CDs
Use the optional Sony compact disc single
adapter (CSA-8) to protect the CD player from
damage.
adapter (CSA-8) to protect the CD player from
damage.
Fuse (10 A)
*I-3-043-466-12*
(1)
Dismounting the unit
1
After taking off the front panel, press the
clip inside the front cover with a thin
screwdriver, and gently pry the front
cover free.
clip inside the front cover with a thin
screwdriver, and gently pry the front
cover free.
2
Repeat step 1 on the left side.
The front cover is removed.
The front cover is removed.
3
Use a thin screwdriver to push in the clip
on the left side of the unit, then pull out
the left side of the unit until the catch
clears the mounting.
on the left side of the unit, then pull out
the left side of the unit until the catch
clears the mounting.
4
Repeat step 3 for the right side.
5
Slide the unit out of the mounting.
Maintenance
Fuse replacement
When replacing the fuse, be sure to use one
matching the amperage rating stated on the
original fuse. If the fuse blows, check the power
connection and replace the fuse. If the fuse blows
again after replacement, there may be an internal
malfunction. In such a case, consult your nearest
Sony dealer.
matching the amperage rating stated on the
original fuse. If the fuse blows, check the power
connection and replace the fuse. If the fuse blows
again after replacement, there may be an internal
malfunction. In such a case, consult your nearest
Sony dealer.
Warning
Never use a fuse with an amperage rating
exceeding the one supplied with the unit as this
could damage the unit.
Never use a fuse with an amperage rating
exceeding the one supplied with the unit as this
could damage the unit.
Cleaning the connectors
The unit may not function properly if the
connectors between the unit and the front panel
are not clean. In order to prevent this, open the
front panel by pressing (RELEASE), then detach
it and clean the connectors with a cotton swab
dipped in alcohol. Do not apply too much force.
Otherwise, the connectors may be damaged.
connectors between the unit and the front panel
are not clean. In order to prevent this, open the
front panel by pressing (RELEASE), then detach
it and clean the connectors with a cotton swab
dipped in alcohol. Do not apply too much force.
Otherwise, the connectors may be damaged.
Main unit
Back of the front panel
Notes
• For safety, turn off the engine before cleaning the
• For safety, turn off the engine before cleaning the
connectors and remove the key from the ignition
switch.
switch.
• Never touch the connectors directly with your
fingers or any metal device.
Notes
• Be sure not to drop the panel when detaching it
• Be sure not to drop the panel when detaching it
from the unit.
• If you detach the panel while the unit is still turned
on, the power will turn off automatically to
prevent the speakers from being damaged.
prevent the speakers from being damaged.
• When carrying the front panel with you, use the
supplied front panel case.
Attaching the front panel
Attach part A of the front panel to part B of the
unit as illustrated and push the left side into
position until it clicks.
unit as illustrated and push the left side into
position until it clicks.
Notes
• Be sure not to attach the front panel upside down.
• Do not press the front panel too hard against the
• Be sure not to attach the front panel upside down.
• Do not press the front panel too hard against the
unit when attaching it.
• Do not press too hard or put excessive pressure on
the display window of the front panel.
• Do not expose the front panel to direct sunlight or
heat sources such as hot air ducts, and do not leave
it in a humid place. Never leave it on the
dashboard of a car parked in direct sunlight or
where there may be a considerable rise in
temperature.
it in a humid place. Never leave it on the
dashboard of a car parked in direct sunlight or
where there may be a considerable rise in
temperature.
Caution alarm
If you turn the car ignition off without removing
the front panel, the caution alarm will beep for a
few seconds.
If you connect an optional power amplifier and
do not use the built-in amplifier, the beep sound
will be deactivated.
the front panel, the caution alarm will beep for a
few seconds.
If you connect an optional power amplifier and
do not use the built-in amplifier, the beep sound
will be deactivated.
A
B
(OFF)
(RELEASE)
4 mm
(
(
3
/
16
in.)