Canon VB-R13VE Manual
70
The specified path <the drive name and the folder name> is
unavailable.
unavailable.
[Enable camera specification file] has been selected in the
[Environmental Settings] and an invalid drive or folder was
specified as the camera specification file’s save location. Please
re-specify the camera specification file save location.
[Environmental Settings] and an invalid drive or folder was
specified as the camera specification file’s save location. Please
re-specify the camera specification file save location.
Unable to write to the specified folder: <the folder name>.
[Enable camera specification file] was selected in the
[Environmental Settings], however an invalid folder was specified
as the camera specification file’s save location. Please re-specify
the camera specification file save location.
[Environmental Settings], however an invalid folder was specified
as the camera specification file’s save location. Please re-specify
the camera specification file save location.
File does not exist.
The file specified in [Set from file] does not exist. Make sure a valid
file is specified.
file is specified.
The IPv4 address is already in use or no configurable IPv4
addresses are available.
Check the camera list and Basic Camera Settings.
addresses are available.
Check the camera list and Basic Camera Settings.
The IPv4 address specified in [Basic Camera Settings] or [Set from
file] is already in use by a camera in the camera list. Review the
specification of IPv4 address.
file] is already in use by a camera in the camera list. Review the
specification of IPv4 address.
The IPv4 address is already in use or no configurable IPv4
addresses are available.
Check the camera list and Set from file.
addresses are available.
Check the camera list and Set from file.
The camera(s) with the following IP address has already been
added to the trusted sites.
<IP address>
added to the trusted sites.
<IP address>
When executing [Maintenance] > [Add to Trusted Sites], you are
trying to register an address that is already registered with the
trusted sites. Recheck the address to be registered.
trying to register an address that is already registered with the
trusted sites. Recheck the address to be registered.
A camera that requires registration of administrator account was
found.
Please register with Camera Settings > Register Administrator
Account.
found.
Please register with Camera Settings > Register Administrator
Account.
This is a message displayed when a camera with no registered
administrator account is included in the search result of [Search
Cameras]. Register an administrator account for the relevant
camera.
administrator account is included in the search result of [Search
Cameras]. Register an administrator account for the relevant
camera.
The camera contained in the file with the following IP address
could not be added. Please check the contents of the file.
<IP address>
could not be added. Please check the contents of the file.
<IP address>
When you tried to add cameras by selecting [File] > [Open] to load
a file including only IPv4 addresses (P. 47), connection to the
cameras with the specified IPv4 addresses failed. Make sure that
the IPv4 address, administrator name, and administrator password
are specified correctly.
a file including only IPv4 addresses (P. 47), connection to the
cameras with the specified IPv4 addresses failed. Make sure that
the IPv4 address, administrator name, and administrator password
are specified correctly.
The file cannot be used, because it has been created with a newer
version of the Camera Management Tool. Please upgrade the
version of the Camera Management Tool.
version of the Camera Management Tool. Please upgrade the
version of the Camera Management Tool.
By selecting [File] > [Open] or [Camera Settings] > [Set from file],
you are trying to load a file created with a newer version of the
camera management tool currently used. Upgrade the camera
management tool and try again.
you are trying to load a file created with a newer version of the
camera management tool currently used. Upgrade the camera
management tool and try again.
The administrator name is already in use.
The administrator names specified in [Search Cameras] or
[Common Authentication Information Setting] are duplicated.
Recheck the specification for the administrator name.
[Common Authentication Information Setting] are duplicated.
Recheck the specification for the administrator name.
Administrator name is invalid. Set within 5 to 15 characters.
Invalid number of characters are used for administrator name. Use
5 – 15 characters to set an administrator name.
5 – 15 characters to set an administrator name.
Administrator password is invalid. Set within 8 to 31 characters.
Invalid number of characters are used for administrator password
except administrator “root”. Use 8 to 31 characters to set
administrator password except administrator “root”.
except administrator “root”. Use 8 to 31 characters to set
administrator password except administrator “root”.
Administrator password is invalid. Set within 8 characters.
Invalid number of characters are used for administrator password
for administrator “root”. Use up to 8 characters (excluding blank) to
set administrator password for administrator “root”.
for administrator “root”. Use up to 8 characters (excluding blank) to
set administrator password for administrator “root”.
Operation failed camera(s) exist. Please check your message.
Some camera(s) had an error when executing [Software Update
Utility], [Memory Card Operations], [Back Up Settings], or [Restore
Settings] from the [Maintenance] menu.
Check the content of [Message] row displayed in respective
windows during execution.
Utility], [Memory Card Operations], [Back Up Settings], or [Restore
Settings] from the [Maintenance] menu.
Check the content of [Message] row displayed in respective
windows during execution.
Encryption Password is invalid.
Invalid characters were used in [Encryption Password] when
executing [Back Up Settings] or [Restore Settings] in the
[Maintenance] menu. Only enter alphanumeric characters,
symbols, or spaces in [Encryption Password].
executing [Back Up Settings] or [Restore Settings] in the
[Maintenance] menu. Only enter alphanumeric characters,
symbols, or spaces in [Encryption Password].
Message
Description