Netgear SRX5308 – ProSafe® Quad WAN Gigabit SSL VPN Firewall Installation Guide
)NSTALLATION
ProSafe
®
Gigabit Quad WAN SSL VPN Firewall SRX5308
Start Here
Follow these instructions to set up your VPN firewall.
You can also consult the
online Reference Manual or the NETGEAR Knowledge base at http://
kbserver.netgear.com. A link to the online Reference Manual is on the ProSafe
kbserver.netgear.com. A link to the online Reference Manual is on the ProSafe
®
Gigabit
Quad WAN SSL VPN Firewall SRX5308 Resource CD.
Prepare to Install Your Firewall
This guide provides instructions for setting up a simple dual WAN port rollover
configuration. Refer to the Reference Manual for other WAN port configuration options.
configuration. Refer to the Reference Manual for other WAN port configuration options.
First, Connect the SRX5308
1. Connect the cables between the SRX5308, two modems, and a computer
a. Turn off and unplug the broadband modems.
b. Insert an Ethernet cable from a modem into the WAN1 port of the SRX5308.
c. Insert an Ethernet cable from the other modem into the WAN2 port of the
c. Insert an Ethernet cable from the other modem into the WAN2 port of the
SRX5308.
d. Insert the Ethernet cable that came with your VPN firewall into a LAN port on
the firewall and insert the other end into the Ethernet port of your computer.
Your network cables are connected and you are ready to restart your network.
2. Restart your network in the correct sequence
2
4
1
3
5
Warning: Failure to restart your network in the correct sequence could prevent you
from connecting to the Internet.
a. First, power on the broadband modems. Wait approximately 2 minutes until they
from connecting to the Internet.
a. First, power on the broadband modems. Wait approximately 2 minutes until they
power up.
b. Now, power on the SRX5308.
c. Last, turn on your computer.
d. Before configuring your SRX5308, check the status lights to verify the
c. Last, turn on your computer.
d. Before configuring your SRX5308, check the status lights to verify the
following:
1 - Power (green). The power light should turn solid green. If it does not turn
solid green, see the Troubleshooting section of the full manual.
solid green, see the Troubleshooting section of the full manual.
2 -Test (amber). When you first turn on the router, the amber test light will be lit
for approximately 2 minutes. If it is still on after several minutes, see the
Troubleshooting Tips below.
for approximately 2 minutes. If it is still on after several minutes, see the
Troubleshooting Tips below.
3 - LAN (green/amber). Each port has a green light on the left side of the port. If
on the port has a link, if it blinks, the port is active. Each port has a green and
amber light on the right side of the port. If the green light is on, the port is
1000Mbps, if the amber light is on, the port is 100Mbps, if neither light is on, the
port is 10Mbps. If a LAN light is not lit, ensure that its Ethernet cable is securely
attached at both ends, and that the computer is turned on.
on the port has a link, if it blinks, the port is active. Each port has a green and
amber light on the right side of the port. If the green light is on, the port is
1000Mbps, if the amber light is on, the port is 100Mbps, if neither light is on, the
port is 10Mbps. If a LAN light is not lit, ensure that its Ethernet cable is securely
attached at both ends, and that the computer is turned on.
4 - WAN (green/amber). Each port has a green light on the left side of the port
and a green and amber light on the right side of the port. The lights operate the
same as the LAN lights described above.
and a green and amber light on the right side of the port. The lights operate the
same as the LAN lights described above.
5 - DMZ (green): If this light is on, the port is configured as a DMZ port.
Next, Configure the SRX5308 for Internet Access
Before you begin, be sure you have the configuration parameters from your ISP handy.
1. Log in to the firewall
1. Log in to the firewall
a. Use a browser to connect to https://192.168.1.1
Note: To connect to the firewall, your computer needs to be configured to obtain an IP
address automatically via DHCP. If you need instructions on how to do this, please refer to
the online reference manual. A link to the manual is on your ProSafe
address automatically via DHCP. If you need instructions on how to do this, please refer to
the online reference manual. A link to the manual is on your ProSafe
®
Gigabit Quad WAN
SSL VPN Firewall SRX5308 Resource CD.
b. For security reasons, the
firewall has its own user name
and password.
When prompted, enter admin
and password.
When prompted, enter admin
for the firewall User Name and
password for the firewall Pass-
word.
password for the firewall Pass-
word.
c. Click Login. You are now connected to the firewall.
The Web Support tab on the main menu contains links to the online NETGEAR
SRX5308 product documentation and support Knowledge base. Be aware that
the default login time-out is 5 minutes of inactivity, after which automatic logout
will occur.
SRX5308 product documentation and support Knowledge base. Be aware that
the default login time-out is 5 minutes of inactivity, after which automatic logout
will occur.
d. Click Network Configuration, WAN Settings. The WAN screen will display.
A table of settings for the WAN ports is shown.
2. Connect to the Internet
a. Click on the Edit button at the right of the WAN1 row. The WAN1 ISP Settings
screen will be displayed. Click Auto Detect at the bottom of the WAN1 ISP
Settings screen. The firewall will automatically attempt to detect your
connection type. If you know your ISP connection type, you can manually
configure the firewall settings on the WAN1 ISP screen. If connecting manually,
click Apply to save your settings.
Settings screen. The firewall will automatically attempt to detect your
connection type. If you know your ISP connection type, you can manually
configure the firewall settings on the WAN1 ISP screen. If connecting manually,
click Apply to save your settings.
b. When finished, click Test to verify that the Internet connection is active.
c. Select the WAN2 ISP tab and complete the same steps you completed in steps a
and b.
SRX5308_IG.fm Page 1 Friday, December 14, 2012 12:37 PM