Netgear JFS524 - 24 Port 10/100 Mbps Fast Ethernet Switch Installation Guide
Installation Guide
ProSafe
®
24-port 10/100Mbps Switch JFS524
Start Here
Estimated Installation Time: 5–10 minutes
Unpack the Box and Verify the Contents
When you open the box, verify that you received everything. The package includes:
•
ProSafe
®
24-port 10/100Mbps Switch JFS524
•
AC power cord
•
Rack-mounting kit
•
Installation Guide (this document)
If you do not have everything listed above, see the support information card for
contact information. If you are missing the support information card, get contact
information at
contact information. If you are missing the support information card, get contact
information at
http://www.NETGEAR.com
in the Technical Support section.
Prepare to Install the Switch
Decide where you want to place the switch. Find a flat horizontal surface such as a
table, desk or shelf. The switch comes with rack-mounting screws. You can use the
screws if you want to mount the switch in an equipment rack. Make sure the
selected location is:
table, desk or shelf. The switch comes with rack-mounting screws. You can use the
screws if you want to mount the switch in an equipment rack. Make sure the
selected location is:
•
Not in direct sunlight or near a heater or heating vent.
•
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space
on all sides of the switch.
•
Well ventilated (especially if it is in a closet).
Also, you will need one Category 5e (Cat 5e) Ethernet cable with RJ-45 connectors
for each device you want to connect to the switch. Each Ethernet cable must be less
than 328 feet (100 meters).
for each device you want to connect to the switch. Each Ethernet cable must be less
than 328 feet (100 meters).
Install the Switch and Connect the Other Devices
1.
Place the switch on a flat surface or mount in a rack.
2.
For each device, insert one end of an Ethernet cable into the port in the device
and insert the other end into one of the Ethernet ports on the switch.
3.
Connect the power cord into the back of the switch and then plug the cord to
an AC power source (such as a wall socket or power strip). The Power light
should light up.
an AC power source (such as a wall socket or power strip). The Power light
should light up.
4.
Check the LEDs to confirm that all connections are correct.
Specifications
LED
Activity
Power
• On: Switch has power.
• Off: No power.
RJ-45 ports
• Top LED on/Blink: Link/Activity
• Bottom LED Off/Green: 10 Mbps/100Mbps.
12VDC 1.2A
8
7
6
5
4
3
2
1
LOCAL
10/100M
INTERNET
OFF
ON
Power
Technical Specifications
Standards Compliance
IEEE 802.3i 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX
Fast Ethernet, IEEE 802.3x full-duplex Flow Control,
compatible with all major network software
Fast Ethernet, IEEE 802.3x full-duplex Flow Control,
compatible with all major network software
Network Interface
Twenty-four (24) 10/100 Mbps Ethernet RJ-45 ports
MAC Address
4K
AC Power
100-240VAC 50-60Hz, 1.2A max., localized to country of sale
Power Consumption
5.9W max
Weight
1.43 kg (3.15 lb)
Dimensions (H x W x D)
43 x 330 x 173 mm (1.7 x 13 x 6.8 in)
Operating Temperature
0 to 50° C (32 to 122° F)
Operating Humidity
90% maximum relative humidity, non-condensing
Electromagnetic
Compliance
Compliance
CE mark (commercial), FCC Part 15 Class A, EN 55022
(CISPR 22) Class A, VCCI Class A, C-Tick, KCC
(CISPR 22) Class A, VCCI Class A, C-Tick, KCC
Safety Agency
Approvals
Approvals
UL listed (UL 60950-1)/CUL, CB, CCC